Grizzly G0495X owner manual Recommended Adjustments, Factory adjustments that should be verified

Page 19

Before starting the jointer, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and safety features on this machine. Failure to follow this warning could result in serious personal injury or even death!

To test run the machine:

1.Make sure you understand the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Connect the machine to the power source. The power light will illuminate.

—If the light does not illuminate, check the power connection.

4.Push the STOP button in, then twist it clock- wise so it pops out. When the STOP button pops out, the switch is reset and ready for operation (see Figure 15).

7)3

4

4

34/0 "UTTON

Figure 15. Resetting the STOP button.

5.Verify that the machine is operating correctly by pushing the START button.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

G0495X 8" Jointer w/Digital Readout

6.Press the STOP button to stop the machine.

7.WITHOUT resetting the switch, press the START button. The machine should not start.

—If the machine does not start, the STOP button safety feature is working correctly. The test run is complete.

—If the machine does start (with the STOP button pushed in), immediately disconnect power to the machine. The STOP button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

Recommended

Adjustments

For your convenience, the adjustments listed below have been performed at the factory and no further setup is required to operate your machine.

However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure the best possible results from your new machine.

Step-by-step instructions for these adjustments can be found in SECTION 7: SERVICE.

Factory adjustments that should be verified:

1.Table Parallelism (Page 34).

2.Infeed Table Calibration (Page 38).

3.Digital Sensor and Readout Calibration (Page 39).

4.Fence Stop Settings (Page 40).

5.Verify V-Belt Tension Adjustment (Page 42).

-17-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model G0495X Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Machine Data Sheet Cutterhead Info Identification Control Panel & Digital Sensor Features  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Additional Safety Instructions for Jointers 220V Operation Circuit RequirementsUnpacking SetupSetup Safety Items Needed for SetupBox 1 Qty InventoryFloor Load Clean UpPlacement Location Site ConsiderationsTo lift the jointer Moving & Placing JointerMounting to Shop Floor Bolting to Concrete FloorsTo connect the machine to a dust collector Dust Collection Setting OutfeedTo set the outfeed table height Digital Readout Batteries To install the AAA batteries in the control panelTest Run Factory adjustments that should be verified Recommended AdjustmentsOperations Operation SafetyPage Digital Sensor Digital Sensor Readout-278 To use the digital readout Digital Readout#/22%#4 Stock Inspection RequirementsSquaring Stock To surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH8029-5 Piece Safety Kit AccessoriesT20448T20452 T20501 T20456 H0736 Half-mask respirator with disposable Cartridge filtersUnpainted Cast Iron MaintenanceCleaning ScheduleTroubleshooting ServiceMotor & Electrical Cutting Possible Cause Possible SolutionChecking Outfeed Table Checking/Adjusting Table ParallelismTools Needed Qty Checking Infeed Table Adjusting Table ParallelismFront eccentric bushings To adjust the table parallelismTo rotate or change a carbide insert Replacing Carbide InsertsTo calibrate the depth scale Setting Infeed TableSetting Outfeed Table Height on Calibrating InfeedTo calibrate the sensor and display To adjust the cutterhead guardCalibrating Digital Sensor & Readout Cutterhead GuardTo set the 45˚ inward fence stop Setting Fence StopsTo set the 45˚ outward fence stop To set the 90˚ fence stopBelt To adjust/replace the V-beltTo align the pulleys Pulley AlignmentSteps Electrical Components Control panel wiringSee Figure Wiring DiagramDescription Fence Parts Breakdown & List+  .+ -& Base Parts Breakdown & List+- +& ++ +* +, + Table Parts Breakdown & ListStand Parts Breakdown & List Label Placement Stand Parts List22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%

G0495X specifications

The Grizzly G0495X is a versatile and powerful tool designed for woodworking enthusiasts and professionals alike. This hybrid table saw combines cutting-edge technology with traditional craftsmanship, ensuring precision and efficiency in every project.

At the heart of the G0495X is its robust 3 HP motor, which delivers exceptional power to handle even the toughest hardwoods with ease. This heavy-duty drive system ensures smooth and reliable performance, reducing the risk of motor burnout during extended use. The saw's belt drive system further enhances its capability, providing a high degree of torque for challenging cutting tasks.

One of the standout features of the G0495X is its large cast iron table. Measuring a generous 30” x 42”, it provides ample workspace for handling larger materials while ensuring stability and accuracy in cuts. The precision-ground surface of the table reduces friction, allowing for smoother movement of wood across the surface. Additionally, the table features an integrated T-style miter gauge slot, offering the user versatility for various cutting angles.

In terms of safety, the G0495X is equipped with several important features. The riving knife and blade guard help to prevent kickbacks, making it safer to use, particularly for novices. The easy-to-use height and bevel adjustment mechanisms allow users to make quick changes to the blade settings for different cut types.

The saw also incorporates advanced dust collection capabilities. With a 4” dust port, it connects to most standard dust collection systems, significantly reducing the mess and maintaining a clean workspace. This feature not only keeps the area tidy but also enhances the user’s visibility while working.

Another notable characteristic of the Grizzly G0495X is its versatility. This table saw can handle various cutting tasks, from rip cuts to crosscuts, making it suitable for a range of woodworking projects, including furniture making, cabinetry, and more. The built-in extension table and side wings also expand the cutting capacity for larger projects.

Overall, the Grizzly G0495X stands out as a reliable and powerful table saw equipped with premium features that cater to both amateur and professional woodworkers. Its combination of performance, safety, and advanced technologies makes it an excellent investment for anyone serious about woodworking.
Top Page Image Contents