Grizzly G0444Z instruction manual Maintenance, Cleaning, Lubrication, Miscellaneous

Page 40

SECTION 7: MAINTENANCE

!	Always	disconnect
	power	to the machine
	before performing main-
	tenance. Failure to do
	this may result in serious
	personal injury.

Cleaning

Clean the Model G0444/G0444Z according to the schedule below to ensure maximum perfor- mance. NoteÑThe following maintenance sched- ule assumes the saw is being used every day.

Daily:

¥Wipe down the table surface and grooves with a rust preventive such as SLIPIT¨ (Grizzly items G5562 & G5563).

¥Clean the pitch and resin from the saw blade with OxiSolv¨ Blade & Bit Cleaner (Grizzly item G1955).

Weekly:

¥Clean the motor housing with compressed air.

¥Wipe down the fence rails with a dry silicon lubricant such as Spraway¨ Silicon Lubricant (Grizzly item G2545).

Lubrication

Lubricate the areas indicated below every 12 months.

1.Blade angling trunnions. These should be lubricated with 6 or 7 drops of light machine oil.

2.Blade height trunnion. This should also be lubricated with 6 or 7 drops of light machine oil.

3.The 2 worm gears should be lubricated with an automotive wheel bearing grease.

These points can be reached from the back of the machine. Check all adjustments after lubricating.

Miscellaneous

Always be aware of the condition of your machine. Routinely check the condition of the fol- lowing items and repair or replace as necessary:

•Mounting bolts

•Power switch

•Saw blade

•Blade guard

-38-	G0444/G0444Z 10" Table Saw

Image 40

Contents Table SAW Model G0444/G0444ZPage Table Of Contents Reference Info Safety Safety Instructions For Power ToolsLength Additional Safety Instructions For Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to avoid the most common causes of kickback Safety Accessories Push SticksZero Clearance Table Inserts FeatherboardsCommon Definitions, Terms And Phrases Introduction CommentaryCircuit Requirements Voltage & Amperage DrawCircuit Breaker Plug & ReceptacleCircuit Capacity GroundingExtension Cords Machine Features About this Section Parts Inventory SET UPUnpacking Located in the Blade Guard Hardware Bag Cast Iron Extension Wings G0444Z Circle Floor Load Clean Up Site ConsiderationsWorking Clearances Beginning Assembly Stand Tools NeededRubber Feet To install the rubber feetComponents and Hardware Needed Qty To install the handwheels To install the dust portDust Port Handwheels To install the motor MotorInstalled pulley cover G0444/G0444Z 10 Table Saw To install the extension wings Extension WingsSwitch To install the blade guardTo install the switch BladeFenceMiter Gauge Blade Guard To assemble the miter gaugeIncorrect blade guard alignment G0444/G0444Z 10 Table Saw Table Insert To install the table insertRepeat steps Power Cord G0444 WiringRecommended Adjustments Recommended adjustment checklistStart Up Starting the machineRip blade features OperationsGeneral Blade SelectionLaminant blade features Combination blade featuresDado Blades To make a 90˚ crosscut using the miter gauge CrosscuttingRipping To make a rip cutDado Cutting Single-blade dado cut G0444/G0444Z 10 Table SawUsing a standard saw blade Dado will be too bigRabbet Cutting To attach a sacrificial fenceCutting rabbets with the standard blade Maintenance CleaningLubrication MiscellaneousBeltsBearings Maintenance Log Date Approximate Hours Of Use Maintenance PerformedService Adjustments About ServiceBlade Parallelism To do this may resultTo Shift The Trunnion To Shim The Trunnion¡ blade parallelism measurement 45˚ & 90˚ Stops Worm Gears Reference Info Aftermarket AccessoriesZero-Clearance Table Insert H0627 OxiSolv Blade & Bit Cleaner G1955 Shop FOX Push Stick H3308Shop FOX Featherboard H3309 Slipit Lubricant G5562 & G5563Machine Data Sheet Model G0444Z Contractor Style SAW 38A G0444/G0444Z 10 Table Saw 139 Description Motor Pulley Troubleshooting Symptom Possible Cause Corrective ActionPage G0444 & G0444Z Wiring Diagrams Warranty & Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog