Grizzly G0444Z instruction manual Operations, General, Blade Selection, Rip blade features

Page 32

SECTION 6: OPERATIONS

General

Damage to your eyes, lungs, and ears could result from failure to wear safety glasses, a respirator, and hearing protec- tion while sanding with this machine.

Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery.

Keep the blade guard in the down position at all times. Failure to do this could result in serious personal injury or death.

-30-

Blade Selection

Rip blade features:

¥Best for cutting with the grain of the work- piece.

¥20-40 teeth.

¥Flat-top ground tooth profile.

¥Large gullets for large chip removal.

Figure 39. Rip blade.

Crosscut blade features:

¥Best for cutting across the grain of the work- piece.

¥60-80 teeth.

¥Alternate top bevel tooth profile.

¥Small hook angle and a shallow gullet.

Figure 40. Crosscutting blade.

G0444/G0444Z 10" Table Saw

Image 32

Contents Table SAW Model G0444/G0444ZPage Table Of Contents Reference Info Safety Safety Instructions For Power ToolsLength Additional Safety Instructions For Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Safety Accessories Push SticksZero Clearance Table Inserts FeatherboardsCommon Definitions, Terms And Phrases Introduction CommentaryCircuit Requirements Voltage & Amperage DrawCircuit Breaker Plug & ReceptacleExtension Cords GroundingCircuit Capacity Machine Features Unpacking SET UPAbout this Section Parts Inventory Located in the Blade Guard Hardware Bag Cast Iron Extension Wings G0444Z Circle Working Clearances Clean Up Site ConsiderationsFloor Load Beginning Assembly Stand Tools NeededComponents and Hardware Needed Qty To install the rubber feetRubber Feet Dust Port Handwheels To install the dust portTo install the handwheels To install the motor MotorInstalled pulley cover G0444/G0444Z 10 Table Saw To install the extension wings Extension WingsSwitch To install the blade guardTo install the switch BladeFenceMiter Gauge Blade Guard To assemble the miter gaugeIncorrect blade guard alignment G0444/G0444Z 10 Table Saw Repeat steps To install the table insertTable Insert Power Cord G0444 WiringRecommended Adjustments Recommended adjustment checklistStart Up Starting the machineRip blade features OperationsGeneral Blade SelectionDado Blades Combination blade featuresLaminant blade features To make a 90˚ crosscut using the miter gauge CrosscuttingRipping To make a rip cutDado Cutting Single-blade dado cut G0444/G0444Z 10 Table SawUsing a standard saw blade Dado will be too bigRabbet Cutting To attach a sacrificial fenceCutting rabbets with the standard blade Maintenance CleaningLubrication MiscellaneousBeltsBearings Maintenance Log Date Approximate Hours Of Use Maintenance PerformedService Adjustments About ServiceBlade Parallelism To do this may resultTo Shift The Trunnion To Shim The Trunnion¡ blade parallelism measurement 45˚ & 90˚ Stops Worm Gears Zero-Clearance Table Insert H0627 Aftermarket AccessoriesReference Info OxiSolv Blade & Bit Cleaner G1955 Shop FOX Push Stick H3308Shop FOX Featherboard H3309 Slipit Lubricant G5562 & G5563Machine Data Sheet Model G0444Z Contractor Style SAW 38A G0444/G0444Z 10 Table Saw 139 Description Motor Pulley Troubleshooting Symptom Possible Cause Corrective ActionPage G0444 & G0444Z Wiring Diagrams Warranty & Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog