Grizzly G0444Z instruction manual Extension Wings, To install the extension wings

Page 25

Extension Wings

Components and Hardware Needed:

Qty

Extension Wings

2

Hex Bolts 7Ú16"-14 x 11Ú4"

6

Lock Washers 7Ú16"

6

Flat Washers 7Ú16"

6

Tools Needed:

 

17mm Wrench or Socket

1

Straightedge

1

To install the extension wings:

 

1.Align the extension wing holes with the holes on the cast iron table edges.

2.Using a 17mm wrench, secure the extension wings to the cast iron table with the hex bolts, the lock washers, and the flat washers.

3.Lay a straightedge across the extension wings and cast iron table surface.

ÑIf the straightedge lays flat across all three surfaces, then skip ahead to the next sub-section.

ÑIf either extension wings tilts down, loosen it and place a strip of masking tape along the bottom edge of the table (Figure 25).

Figure 25. Masking tape location for adjusting

extension table up.

ÑIf either extension wing tilts up, loosen it and place a strip of masking tape along the top edge of the table (Figure 26).

Figure 26. Masking tape location for adjusting

the extension wing down.

4.Tighten the extension wing bolts and repeat step 3.

5.Once all three table surfaces are level, remove the excess masking tape with a razor blade.

G0444/G0444Z 10" Table Saw

-23-

Image 25
Contents Model G0444/G0444Z Table SAWPage Table Of Contents Reference Info Safety Instructions For Power Tools SafetyLength Additional Safety Instructions For Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to avoid the most common causes of kickback Push Sticks Safety AccessoriesZero Clearance Table Inserts FeatherboardsCommon Definitions, Terms And Phrases Commentary IntroductionVoltage & Amperage Draw Circuit RequirementsCircuit Breaker Plug & ReceptacleCircuit Capacity GroundingExtension Cords Machine Features About this Section Parts Inventory SET UPUnpacking Located in the Blade Guard Hardware Bag Cast Iron Extension Wings G0444Z Circle Floor Load Clean Up Site ConsiderationsWorking Clearances Tools Needed Beginning Assembly StandRubber Feet To install the rubber feetComponents and Hardware Needed Qty To install the handwheels To install the dust portDust Port Handwheels Motor To install the motorInstalled pulley cover G0444/G0444Z 10 Table Saw Extension Wings To install the extension wingsTo install the blade guard SwitchTo install the switch BladeFenceTo assemble the miter gauge Miter Gauge Blade GuardIncorrect blade guard alignment G0444/G0444Z 10 Table Saw Table Insert To install the table insertRepeat steps G0444 Wiring Power CordRecommended adjustment checklist Recommended AdjustmentsStart Up Starting the machineOperations Rip blade featuresGeneral Blade SelectionLaminant blade features Combination blade featuresDado Blades Crosscutting To make a 90˚ crosscut using the miter gaugeTo make a rip cut RippingSingle-blade dado cut G0444/G0444Z 10 Table Saw Dado CuttingDado will be too big Using a standard saw bladeTo attach a sacrificial fence Rabbet CuttingCutting rabbets with the standard blade Cleaning MaintenanceLubrication MiscellaneousBeltsBearings Date Approximate Hours Of Use Maintenance Performed Maintenance LogAbout Service Service AdjustmentsBlade Parallelism To do this may resultTo Shim The Trunnion To Shift The Trunnion¡ blade parallelism measurement 45˚ & 90˚ Stops Worm Gears Reference Info Aftermarket AccessoriesZero-Clearance Table Insert H0627 Shop FOX Push Stick H3308 OxiSolv Blade & Bit Cleaner G1955Shop FOX Featherboard H3309 Slipit Lubricant G5562 & G5563Machine Data Sheet Model G0444Z Contractor Style SAW 38A G0444/G0444Z 10 Table Saw 139 Description Motor Pulley Symptom Possible Cause Corrective Action TroubleshootingPage G0444 & G0444Z Wiring Diagrams Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog