Grizzly G0444Z instruction manual ¡ blade parallelism measurement

Page 45

45û Bevel

!

#1

#4

		Front

	A



#2	#3

Figure 56. 45¡ blade parallelism measurement.

3.Tighten down one trunnion bolt a small amount and then move on to each of the oth- ers, tightening each down the same amount.

4.Continue to rotate through the bolts, tighten- ing them a little each time until they are all secure.

5.Flip the saw rightside up and repeat steps 2- 6 on page 41.

6.Once the miter slot is adjusted parallel to the blade, recheck all measurements and be sure the table mounting bolts are secure.

7.Re-attach the blade guard and the fence.

8.Verify that the blade guard is correctly aligned with the blade.

45û Bevel

!

NOTICE

#1	#4

Front

B

#2#3

Figure 57. 45¡ blade parallelism measurement.

If the trunnion assembly is loosened in the future, make note of the shim locations and re-assemble accordingly.

G0444/G0444Z 10" Table Saw

-43-

Image 45

Contents Model G0444/G0444Z Table SAWPage Table Of Contents Reference Info Safety Instructions For Power Tools SafetyLength Additional Safety Instructions For Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Push Sticks Safety AccessoriesZero Clearance Table Inserts FeatherboardsCommon Definitions, Terms And Phrases Commentary IntroductionVoltage & Amperage Draw Circuit RequirementsCircuit Breaker Plug & ReceptacleGrounding Circuit CapacityExtension Cords Machine Features SET UP About this Section Parts InventoryUnpacking Located in the Blade Guard Hardware Bag Cast Iron Extension Wings G0444Z Circle Clean Up Site Considerations Floor LoadWorking Clearances Tools Needed Beginning Assembly StandTo install the rubber feet Rubber FeetComponents and Hardware Needed Qty To install the dust port To install the handwheelsDust Port Handwheels Motor To install the motorInstalled pulley cover G0444/G0444Z 10 Table Saw Extension Wings To install the extension wingsTo install the blade guard SwitchTo install the switch BladeFenceTo assemble the miter gauge Miter Gauge Blade GuardIncorrect blade guard alignment G0444/G0444Z 10 Table Saw To install the table insert Table InsertRepeat steps G0444 Wiring Power CordRecommended adjustment checklist Recommended AdjustmentsStart Up Starting the machineOperations Rip blade featuresGeneral Blade SelectionCombination blade features Laminant blade featuresDado Blades Crosscutting To make a 90˚ crosscut using the miter gaugeTo make a rip cut RippingSingle-blade dado cut G0444/G0444Z 10 Table Saw Dado CuttingDado will be too big Using a standard saw bladeTo attach a sacrificial fence Rabbet CuttingCutting rabbets with the standard blade Cleaning MaintenanceLubrication MiscellaneousBeltsBearings Date Approximate Hours Of Use Maintenance Performed Maintenance LogAbout Service Service AdjustmentsBlade Parallelism To do this may resultTo Shim The Trunnion To Shift The Trunnion¡ blade parallelism measurement 45˚ & 90˚ Stops Worm Gears Aftermarket Accessories Reference InfoZero-Clearance Table Insert H0627 Shop FOX Push Stick H3308 OxiSolv Blade & Bit Cleaner G1955Shop FOX Featherboard H3309 Slipit Lubricant G5562 & G5563Machine Data Sheet Model G0444Z Contractor Style SAW 38A G0444/G0444Z 10 Table Saw 139 Description Motor Pulley Symptom Possible Cause Corrective Action TroubleshootingPage G0444 & G0444Z Wiring Diagrams Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog