Grizzly G0444Z Rubber Feet, Components and Hardware Needed Qty, To install the rubber feet

Page 21

3. Place the long ÒLÓ side supports over the ends of the short ÒLÓ side supports.

4.Using a 12mm wrench, secure all four ÒLÓ side supports to the saw body with 4 hex bolts, 8 flat washers, 4 lock washers, and 4 hex nuts.

5.Secure each stand leg to the outside of the ÒLÓ side supports with 24 carriage bolts, 24 flat washers, 24 lock washers, and 24 hex nuts (Figure 13).

Stand Leg

Figure 13. Stand leg installation.

6.Secure the flat side supports to the stand legs with 16 carriage bolts, 16 flat washers, 16 lock washers, and 16 hex nuts (Figure 12).

Flat Side Support

Figure 14. Flat side support installation.

Rubber Feet

Components and Hardware Needed:	Qty
Rubber Feet	4
Hex Nuts 1Ú4"-20	4
Flat Washers 1Ú4"	4
Phillips Head Screws 1Ú4"-20 x 1"	4
Tools Needed:
10mm Wrench or Socket	1
Phillips Head Screwdriver	1
To install the rubber feet:

1.Using a 10mm wrench and a Phillips head screwdriver, secure each rubber foot to the stand legs with the Phillips head screws, the hex nuts, and the flat washers (Figure 15).

Figure 15. Rubber feet installation.

2.With the help of an assistant, flip the stand rightside up.

3.Final tighten all of the stand fasteners.

G0444/G0444Z 10" Table Saw

-19-

Image 21

Contents Model G0444/G0444Z Table SAWPage Table Of Contents Reference Info Safety Instructions For Power Tools SafetyLength Additional Safety Instructions For Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Push Sticks Safety AccessoriesZero Clearance Table Inserts FeatherboardsCommon Definitions, Terms And Phrases Commentary IntroductionVoltage & Amperage Draw Circuit RequirementsCircuit Breaker Plug & ReceptacleGrounding Circuit CapacityExtension Cords Machine Features SET UP About this Section Parts InventoryUnpacking Located in the Blade Guard Hardware Bag Cast Iron Extension Wings G0444Z Circle Clean Up Site Considerations Floor LoadWorking Clearances Tools Needed Beginning Assembly StandTo install the rubber feet Rubber FeetComponents and Hardware Needed Qty To install the dust port To install the handwheelsDust Port Handwheels Motor To install the motorInstalled pulley cover G0444/G0444Z 10 Table Saw Extension Wings To install the extension wingsTo install the blade guard SwitchTo install the switch BladeFenceTo assemble the miter gauge Miter Gauge Blade GuardIncorrect blade guard alignment G0444/G0444Z 10 Table Saw To install the table insert Table InsertRepeat steps G0444 Wiring Power CordRecommended adjustment checklist Recommended AdjustmentsStart Up Starting the machineOperations Rip blade featuresGeneral Blade SelectionCombination blade features Laminant blade featuresDado Blades Crosscutting To make a 90˚ crosscut using the miter gaugeTo make a rip cut RippingSingle-blade dado cut G0444/G0444Z 10 Table Saw Dado CuttingDado will be too big Using a standard saw bladeTo attach a sacrificial fence Rabbet CuttingCutting rabbets with the standard blade Cleaning MaintenanceLubrication MiscellaneousBeltsBearings Date Approximate Hours Of Use Maintenance Performed Maintenance LogAbout Service Service AdjustmentsBlade Parallelism To do this may resultTo Shim The Trunnion To Shift The Trunnion¡ blade parallelism measurement 45˚ & 90˚ Stops Worm Gears Aftermarket Accessories Reference InfoZero-Clearance Table Insert H0627 Shop FOX Push Stick H3308 OxiSolv Blade & Bit Cleaner G1955Shop FOX Featherboard H3309 Slipit Lubricant G5562 & G5563Machine Data Sheet Model G0444Z Contractor Style SAW 38A G0444/G0444Z 10 Table Saw 139 Description Motor Pulley Symptom Possible Cause Corrective Action TroubleshootingPage G0444 & G0444Z Wiring Diagrams Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog