Woodstock W1706 owner manual Grounding Requirements, Extension Cords, For 110V Connection Prewired

Page 10

Model W1706 (Mfg. Since 8/10)

ELECTRICAL

Grounding Requirements

In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel— in order to reduce the risk of electric shock.

Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green insulation (with/without yellow stripes) is the equipment- grounding wire. If repair or replacement of the power cord or plug is necessary, do not connect the equipment- grounding wire to a live (current carrying) terminal.

Check with a qualified electrician or service personnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded. If you ever notice that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with a new one.

For 110V Connection (Prewired)

A NEMA 5-15 plug has a grounding prong that must be attached to the equipment-grounding wire inside the included power cord. The plug must only be inserted into a matching receptacle (see Figure 3) that is properly installed and grounded in accordance with all local codes and ordinances.

For 220V Connection (Must Be Rewired)

When converting this machine to 220V operation, you must properly install a NEMA 6-15 grounding plug. The plug must only be inserted into a matching receptacle (see Figure 4) that is properly installed and grounded in accordance with local codes and ordinances.

Extension Cords

We do not recommend using an extension cord with this machine. Extension cords cause voltage drop, which may damage electrical components and shorten motor life.

Voltage drop increases with longer extension cords and the gauge smaller gauge sizes (higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must contain a ground wire, match the required plug and receptacle, and meet the following requirements:

Minimum Gauge Size

14 AWG

Maximum Length (Shorter is Better)

50 ft.

The machine must be properly set up before it is safe to operate. DO NOT connect to the power source until instructed to do so later this manual.

110V GROUNDED

5-15 RECEPTACLE

Grounding Prong

5-15 PLUG

 

Neutral Hot

Figure 3. NEMA 5-15 plug & receptacle.

220V

GROUNDED

6-15 RECEPTACLE

Current Carrying Prongs

 

6-15 PLUG

Grounding Prong

Figure 4. NEMA 6-15 plug & receptacle.

DO NOT modify the provided plug or use an adapter if the plug will not fit your receptacle. If the machine must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel; and after reconnection, the machine must comply with all local codes and ordinances.

-8-

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportBlade Guide Lock Knob Locks the upper blade guides in place Controls and FeaturesBlade Tracking Knob Adjusts and locks the blade tracking Blade Tension Knob Tensions the blade in gradual incrementsSafety Standard Machinery Safety InstructionsSafety Additional Safety for Bandsaws Circuit Requirements Power SupplyCircuit Requirements for 110V Prewired Full-Load Current RatingGrounding Requirements For 110V Connection PrewiredFor 220V Connection Must Be Rewired Extension CordsInventory SetupUnpacking Inventory Figures QtyMachine Placement Cleaning Machine Assembly Setup ProceduresTo assemble the bandsaw, do these steps Installing the table onto Trunnion base Rear Fence Rail Dust Collection Recommended CFM at Dust PortBlade Tracking To center track the blade, do these stepsPower Connection Refer to Adjusting Blade Guide Bearings onTest Run Additional AdjustmentsTo test run the machine, do these steps Tensioning Blade Adjusting Blade Guide Bearings on Page 24 forTo correctly tension the bandsaw blade, do these steps To adjust the positive stop, do these steps Adjusting Positive StopTools Needed Qty Aligning Table Taking measurements for aligning the table with the bladeAligning Miter Gauge Body To align the miter gauge body, do these stepsAdjusting Fence To align the fence with the miter slot, do these stepsAdjusting Blade Support Bearings To adjust the support bearings, do these stepsSupport bearing positioned Adjusting Blade Guide Bearings To adjust the blade guide bearings, do these stepsRotating the blade guide Bearings toward the blade Operations GeneralDisabling & Locking Switch Operation OverviewBasic Controls Cutting Overview Workpiece InspectionBasic Cutting Tips Cutting workpieces with minor WarpingTable Tilt Adjusting Guide PostTo adjust the guide post, do these steps To tilt the table, do these stepsRipping To make a rip cut, do these stepsCrosscutting To make a 90˚ crosscut, do these stepsResawing To resaw a workpiece, do these steps⁄16 Cutting CurvesStacked Cuts To complete a stacked cut, do these stepsBlade Speed To change the blade speed, do these stepsBlade Length Blade InformationBlade Width Blade Care Tooth StyleTooth Pitch Blade BreakageBlade Changes To change the blade, do these stepsAccessories Bandsaw AccessoriesLubrication Cleaning MaintenanceProtecting Table Redressing Rubber Tires ServiceTo redress the rubber tires, do these steps Checking Belt Belt ServiceAdjusting Belt Tension To tension the belt, do these stepsReplacing Belt To replace the belt, do these stepsItems Needed Qty Shimming TableTo shim the table, do these steps Correcting Blade Lead Blade LeadTo skew the fence, do these steps Tool Needed Qty Aligning WheelsSkew the table, do these steps Coplanar conditions Measuring the distance Wheel is out of adjustment Shimming a WheelElectrical Safety Instructions Wiring Diagram Color KEYW1706 Wiring Diagram Troubleshooting Problem Possible CauseParts Cabinet StandCabinet Stand Parts List Body Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents