Woodstock W1706 Test Run, Additional Adjustments, To test run the machine, do these steps

Page 18

Model W1706 (Mfg. Since 8/10)

Test Run

SETUP

Once the assembly is complete, test run your machine to make sure it runs properly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page 52.

If you still cannot remedy a problem, contact our Tech Support at (360) 734-3482 for assistance.

To test run the machine, do these steps:

1.Make sure you understand the safety instructions at the beginning of the manual, and verify that the machine is setup properly.

2.Ensure all tools and objects used during set up are cleared away from the machine.

3.Turn the machine ON.

4.Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises.

—Strange or unusual noises should be investigated and corrected before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

5.Turn the machine OFF.

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses to reduce the risk of injury.

Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery.

Additional Adjustments

After successfully completing the Test Run, the adjustment procedures listed below must be performed to ensure safe and accurate cutting operations (refer to the following subsections for detailed instructions):

•Properly tension the blade (Page 17).

•Adjust the positive stop bolt (Page 18).

•Align the table with the blade (Page 19).

•Square the miter gauge body to the blade (Page 20).

•Align the fence with the blade (Page 21).

•Adjusting the blade support bearings (Page 22).

•Adjusting the blade guide bearings (Page 24).

-16-

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportBlade Guide Lock Knob Locks the upper blade guides in place Controls and FeaturesBlade Tracking Knob Adjusts and locks the blade tracking Blade Tension Knob Tensions the blade in gradual incrementsSafety Standard Machinery Safety InstructionsSafety Additional Safety for Bandsaws Circuit Requirements Power SupplyCircuit Requirements for 110V Prewired Full-Load Current RatingGrounding Requirements For 110V Connection PrewiredFor 220V Connection Must Be Rewired Extension CordsInventory SetupUnpacking Inventory Figures QtyMachine Placement Cleaning Machine Setup Procedures AssemblyTo assemble the bandsaw, do these steps Installing the table onto Trunnion base Rear Fence Rail Dust Collection Recommended CFM at Dust PortBlade Tracking To center track the blade, do these stepsPower Connection Refer to Adjusting Blade Guide Bearings onAdditional Adjustments Test RunTo test run the machine, do these steps Adjusting Blade Guide Bearings on Page 24 for Tensioning BladeTo correctly tension the bandsaw blade, do these steps Adjusting Positive Stop To adjust the positive stop, do these stepsTools Needed Qty Aligning Table Taking measurements for aligning the table with the bladeAligning Miter Gauge Body To align the miter gauge body, do these stepsAdjusting Fence To align the fence with the miter slot, do these stepsAdjusting Blade Support Bearings To adjust the support bearings, do these stepsSupport bearing positioned Adjusting Blade Guide Bearings To adjust the blade guide bearings, do these stepsRotating the blade guide Bearings toward the blade Operations GeneralDisabling & Locking Switch Operation OverviewBasic Controls Cutting Overview Workpiece InspectionBasic Cutting Tips Cutting workpieces with minor WarpingTable Tilt Adjusting Guide PostTo adjust the guide post, do these steps To tilt the table, do these stepsRipping To make a rip cut, do these stepsCrosscutting To make a 90˚ crosscut, do these stepsResawing To resaw a workpiece, do these steps⁄16 Cutting CurvesStacked Cuts To complete a stacked cut, do these stepsBlade Speed To change the blade speed, do these stepsBlade Information Blade LengthBlade Width Blade Care Tooth StyleTooth Pitch Blade BreakageBlade Changes To change the blade, do these stepsAccessories Bandsaw AccessoriesMaintenance Lubrication CleaningProtecting Table Service Redressing Rubber TiresTo redress the rubber tires, do these steps Checking Belt Belt ServiceAdjusting Belt Tension To tension the belt, do these stepsReplacing Belt To replace the belt, do these stepsShimming Table Items Needed QtyTo shim the table, do these steps Blade Lead Correcting Blade LeadTo skew the fence, do these steps Aligning Wheels Tool Needed QtySkew the table, do these steps Coplanar conditions Measuring the distance Wheel is out of adjustment Shimming a WheelElectrical Safety Instructions Wiring Diagram Color KEYW1706 Wiring Diagram Troubleshooting Problem Possible CauseParts Cabinet StandCabinet Stand Parts List Body Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents