Woodstock W1706 owner manual Operation Overview, Disabling & Locking Switch

Page 29

Model W1706 (Mfg. Since 8/10)

Operation Overview

The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand.

Due to the generic nature of this overview, it is not intended to be an instructional guide. To learn more about specific operations, read this entire manual and seek additional training from experienced machine operators, and do additional research outside of this manual by reading "how-to" books, trade magazines, or web sites.

To complete a typical operation, the operator does the following:

1.Examines the workpiece to make sure it is suitable for cutting.

2.Adjusts the fence for the width of the cut and then locks it in place.

3.Adjusts the table tilt, if necessary, to the correct angle of the desired cut.

4.Loosens the guide post lock knob, adjusts the blade guide height to between 1⁄4" and 1" from the top of the workpiece using the guide post elevation handwheel, then tightens the guide post lock knob.

5.Checks to make sure the workpiece can safely pass all the way through the blade without interference from other objects.

6.Puts on safety glasses and a respirator.

7.Starts the dust collector and bandsaw, and waits for the blade to come to full speed.

8.Holds the workpiece firmly and flatly against both the table and fence, and then pushes the workpiece into the blade at a steady and controlled rate until the workpiece moves completely beyond the blade.

The operator is very careful to keep fingers away from the blade and uses a push stick to feed narrow workpieces.

9.Stops the bandsaw.

Disabling & Locking

Switch

The ON/OFF switch can be disabled and locked with the provided padlock (see Figure 34). While the padlock is inserted through the ON button, the motor cannot be started, which reduces the risk of accidental startup by children of unauthorized users.

Padlock

Installed

Figure 34. Padlock installed in the switch.

Children or untrained people can be killed or seriously injured by this machine. If the machine is accessible to children or other people, always disable and lock the switch before leaving the machine unattended. Place the key in a well-hidden or secure location.

NOTICE

The switch can only be disabled if the installed padlock shaft meets the minimum diameter shown below; otherwise, the shaft may be too small to properly disable the switch.

Minimum Shaft Diameter = 0.192" – 0.2" (4.8 – 5mm)

OPERATIONS

-27-

Page 28 Page 30
Image 29
Page 28 Page 30
Contents OWNERS MANUAL Page Contents Woodstock Technical Support IntroductionBlade Tracking Knob Adjusts and locks the blade tracking Controls and FeaturesBlade Guide Lock Knob Locks the upper blade guides in place Blade Tension Knob Tensions the blade in gradual incrementsStandard Machinery Safety Instructions SafetySafety Additional Safety for Bandsaws Circuit Requirements for 110V Prewired Power SupplyCircuit Requirements Full-Load Current RatingFor 220V Connection Must Be Rewired For 110V Connection PrewiredGrounding Requirements Extension CordsUnpacking SetupInventory Inventory Figures QtyMachine Placement Cleaning Machine To assemble the bandsaw, do these steps Setup ProceduresAssembly Installing the table onto Trunnion base Rear Fence Rail Recommended CFM at Dust Port Dust CollectionTo center track the blade, do these steps Blade TrackingRefer to Adjusting Blade Guide Bearings on Power ConnectionTo test run the machine, do these steps Additional AdjustmentsTest Run To correctly tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings on Page 24 forTensioning Blade Tools Needed Qty Adjusting Positive StopTo adjust the positive stop, do these steps Taking measurements for aligning the table with the blade Aligning TableTo align the miter gauge body, do these steps Aligning Miter Gauge BodyTo align the fence with the miter slot, do these steps Adjusting FenceTo adjust the support bearings, do these steps Adjusting Blade Support BearingsSupport bearing positioned To adjust the blade guide bearings, do these steps Adjusting Blade Guide BearingsRotating the blade guide Bearings toward the blade General OperationsOperation Overview Disabling & Locking SwitchBasic Controls Workpiece Inspection Cutting OverviewCutting workpieces with minor Warping Basic Cutting TipsTo adjust the guide post, do these steps Adjusting Guide PostTable Tilt To tilt the table, do these stepsTo make a rip cut, do these steps RippingTo make a 90˚ crosscut, do these steps CrosscuttingTo resaw a workpiece, do these steps ResawingStacked Cuts Cutting Curves⁄16 To complete a stacked cut, do these stepsTo change the blade speed, do these steps Blade SpeedBlade Width Blade InformationBlade Length Tooth Pitch Tooth StyleBlade Care Blade BreakageTo change the blade, do these steps Blade ChangesBandsaw Accessories AccessoriesProtecting Table MaintenanceLubrication Cleaning To redress the rubber tires, do these steps ServiceRedressing Rubber Tires Adjusting Belt Tension Belt ServiceChecking Belt To tension the belt, do these stepsTo replace the belt, do these steps Replacing BeltTo shim the table, do these steps Shimming TableItems Needed Qty To skew the fence, do these steps Blade LeadCorrecting Blade Lead Skew the table, do these steps Aligning WheelsTool Needed Qty Coplanar conditions Shimming a Wheel Measuring the distance Wheel is out of adjustmentWiring Diagram Color KEY Electrical Safety InstructionsW1706 Wiring Diagram Problem Possible Cause TroubleshootingCabinet Stand PartsBody Parts List Cabinet Stand Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents