Woodstock W1706 owner manual Standard Machinery Safety Instructions

Page 6

SAFETY

Model W1706 (Mfg. Since 8/10)

SAFETY

For Your Own Safety,

Read Manual Before Operating Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention mea- sures—this responsibility is ultimately up to the operator!

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury.

This symbol is used to alert the user to useful information about NOTICE proper operation of the equipment, and/or a situation that may

cause damage to the machinery.

Standard Machinery Safety Instructions

OWNER’S MANUAL. Read and understand this owner’s manual BEFORE using machine. Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses.

HAZARDOUS DUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with workpiece materials, and always wear a NIOSH-approved respirator to reduce your risk.

WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips which could cause a loss of workpiece control.

HEARING PROTECTION. Always wear hearing protection when operating or observing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

DISCONNECTING POWER SUPPLY. Always disconnect machine from power supply before servicing, adjusting, or changing cutting tools (bits, blades, cutters, etc.). Make sure switch is in OFF position before reconnecting to avoid an unexpected or unintentional start.

DANGEROUS ENVIRONMENTS. Do not use machinery in wet or rainy locations, cluttered areas, around flammables, or in poorly-lit areas. Keep work area clean, dry, and well- lighted to minimize risk of injury.

-4-

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportBlade Guide Lock Knob Locks the upper blade guides in place Controls and FeaturesBlade Tracking Knob Adjusts and locks the blade tracking Blade Tension Knob Tensions the blade in gradual incrementsSafety Standard Machinery Safety InstructionsSafety Additional Safety for Bandsaws Circuit Requirements Power SupplyCircuit Requirements for 110V Prewired Full-Load Current RatingGrounding Requirements For 110V Connection PrewiredFor 220V Connection Must Be Rewired Extension CordsInventory SetupUnpacking Inventory Figures QtyMachine Placement Cleaning Machine Setup Procedures AssemblyTo assemble the bandsaw, do these steps Installing the table onto Trunnion base Rear Fence Rail Dust Collection Recommended CFM at Dust PortBlade Tracking To center track the blade, do these stepsPower Connection Refer to Adjusting Blade Guide Bearings onAdditional Adjustments Test RunTo test run the machine, do these steps Adjusting Blade Guide Bearings on Page 24 for Tensioning BladeTo correctly tension the bandsaw blade, do these steps Adjusting Positive Stop To adjust the positive stop, do these stepsTools Needed Qty Aligning Table Taking measurements for aligning the table with the bladeAligning Miter Gauge Body To align the miter gauge body, do these stepsAdjusting Fence To align the fence with the miter slot, do these stepsAdjusting Blade Support Bearings To adjust the support bearings, do these stepsSupport bearing positioned Adjusting Blade Guide Bearings To adjust the blade guide bearings, do these stepsRotating the blade guide Bearings toward the blade Operations GeneralDisabling & Locking Switch Operation OverviewBasic Controls Cutting Overview Workpiece InspectionBasic Cutting Tips Cutting workpieces with minor WarpingTable Tilt Adjusting Guide PostTo adjust the guide post, do these steps To tilt the table, do these stepsRipping To make a rip cut, do these stepsCrosscutting To make a 90˚ crosscut, do these stepsResawing To resaw a workpiece, do these steps⁄16 Cutting CurvesStacked Cuts To complete a stacked cut, do these stepsBlade Speed To change the blade speed, do these stepsBlade Information Blade LengthBlade Width Blade Care Tooth StyleTooth Pitch Blade BreakageBlade Changes To change the blade, do these stepsAccessories Bandsaw AccessoriesMaintenance Lubrication CleaningProtecting Table Service Redressing Rubber TiresTo redress the rubber tires, do these steps Checking Belt Belt ServiceAdjusting Belt Tension To tension the belt, do these stepsReplacing Belt To replace the belt, do these stepsShimming Table Items Needed QtyTo shim the table, do these steps Blade Lead Correcting Blade LeadTo skew the fence, do these steps Aligning Wheels Tool Needed QtySkew the table, do these steps Coplanar conditions Measuring the distance Wheel is out of adjustment Shimming a WheelElectrical Safety Instructions Wiring Diagram Color KEYW1706 Wiring Diagram Troubleshooting Problem Possible CauseParts Cabinet StandCabinet Stand Parts List Body Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents