Woodstock W1706 owner manual Adjusting Positive Stop, Tools Needed Qty

Page 20

Model W1706 (Mfg. Since 8/10)

Adjusting Positive Stop

SETUP

After using the table at a tilt of other than 0°, the positive stop allows the table to be quickly and accurately returned to the horizontal position in relation to the blade. This is important for accurate cutting results.

Note: The height of the positive stop is lowered when the table is tilted to the left. Properly re-adjust the positive stop after returning the table to 0° or greater.

Tools Needed

Qty

Wrench 13mm

1

Machinist's Square

1

Phillips Screwdriver

1

To adjust the positive stop, do these steps:

 

1.Make sure the blade is properly tensioned as instructed on the previous page.

2.DISCONNECT BANDSAW FROM POWER!

3.Place the machinist's square flat on the table and against the side of the blade, as shown in Figure 19.

—If the square sits on the table and against the blade without any gaps, no adjustments are necessary.

—If there are gaps between the square, table, and blade, continue with Step 4.

4.Loosen both trunnion lock knobs (see Figure 18) to allow the table to tilt.

5.Loosen the hex nut on the positive stop shown in Figure 20, then adjust the height of the positive stop until the square is flat against the table and blade.

6.When you are satisfied with the setting, re-tighten the hex nut to secure the positive stop in place.

7.Loosen the screw on the tilt scale pointer shown in Figure 18, then align the pointer with the "0" on the scale before re-tightening the screw.

Tilt Scale

 

Lock Knob

& Pointer

 

(1 of 2)

 

 

 

Figure 18. Table tilt controls.

Figure 19. Using a machinist's square to

adjust the table tilt.

Positive Stop

Hex Nut

Figure 20. Positive stop (table tilted to

the right for photo clarity).

-18-

Page 19 Page 21
Image 20
Page 19 Page 21
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportControls and Features Blade Tracking Knob Adjusts and locks the blade trackingBlade Guide Lock Knob Locks the upper blade guides in place Blade Tension Knob Tensions the blade in gradual incrementsSafety Standard Machinery Safety InstructionsSafety Additional Safety for Bandsaws Power Supply Circuit Requirements for 110V PrewiredCircuit Requirements Full-Load Current RatingFor 110V Connection Prewired For 220V Connection Must Be RewiredGrounding Requirements Extension CordsSetup UnpackingInventory Inventory Figures QtyMachine Placement Cleaning Machine To assemble the bandsaw, do these steps Setup ProceduresAssembly Installing the table onto Trunnion base Rear Fence Rail Dust Collection Recommended CFM at Dust PortBlade Tracking To center track the blade, do these stepsPower Connection Refer to Adjusting Blade Guide Bearings onTo test run the machine, do these steps Additional AdjustmentsTest Run To correctly tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings on Page 24 forTensioning Blade Tools Needed Qty Adjusting Positive StopTo adjust the positive stop, do these steps Aligning Table Taking measurements for aligning the table with the bladeAligning Miter Gauge Body To align the miter gauge body, do these stepsAdjusting Fence To align the fence with the miter slot, do these stepsAdjusting Blade Support Bearings To adjust the support bearings, do these stepsSupport bearing positioned Adjusting Blade Guide Bearings To adjust the blade guide bearings, do these stepsRotating the blade guide Bearings toward the blade Operations GeneralDisabling & Locking Switch Operation OverviewBasic Controls Cutting Overview Workpiece InspectionBasic Cutting Tips Cutting workpieces with minor WarpingAdjusting Guide Post To adjust the guide post, do these stepsTable Tilt To tilt the table, do these stepsRipping To make a rip cut, do these stepsCrosscutting To make a 90˚ crosscut, do these stepsResawing To resaw a workpiece, do these stepsCutting Curves Stacked Cuts⁄16 To complete a stacked cut, do these stepsBlade Speed To change the blade speed, do these stepsBlade Width Blade InformationBlade Length Tooth Style Tooth PitchBlade Care Blade BreakageBlade Changes To change the blade, do these stepsAccessories Bandsaw AccessoriesProtecting Table MaintenanceLubrication Cleaning To redress the rubber tires, do these steps ServiceRedressing Rubber Tires Belt Service Adjusting Belt TensionChecking Belt To tension the belt, do these stepsReplacing Belt To replace the belt, do these stepsTo shim the table, do these steps Shimming TableItems Needed Qty To skew the fence, do these steps Blade LeadCorrecting Blade Lead Skew the table, do these steps Aligning WheelsTool Needed Qty Coplanar conditions Measuring the distance Wheel is out of adjustment Shimming a WheelElectrical Safety Instructions Wiring Diagram Color KEYW1706 Wiring Diagram Troubleshooting Problem Possible CauseParts Cabinet StandCabinet Stand Parts List Body Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents