Woodstock W1706 owner manual Correcting Blade Lead, To skew the fence, do these steps

Page 48

Model W1706 (Mfg. Since 8/10)

Blade Lead

SERVICE

Bandsaw blades may wander off the cut line when sawing, as shown in Figure 58—this is called blade lead. Blade lead is usually caused by too fast of a feed rate, a dull or damaged blade, or improper blade tension. If your blade is sharp/undamaged, properly tensioned and you still have blade lead, perform the following procedures.

Correcting Blade Lead

1.Use less pressure when feeding the workpiece through the cut.

2.Make sure that the fence is parallel to the blade line, and the miter gauge body is perpendicular to the blade.

3.Check for proper blade tension. If the blade tension is correct and it is not convenient to replace the blade, compensate for lead by skewing the fence or shifting the table.

Items Needed

Qty

Board 3⁄4"T x 3"W x 17"L

1

Hex Wrench 5mm

1

To skew the fence, do these steps:

 

1.On the wide face of the board, draw a straight line parallel to the long edge.

2.Slide the fence out of the way and cut free-hand along the line. Stop at the halfway point. Turn the bandsaw OFF and wait for the blade to stop.

3.Clamp the board to the bandsaw table without moving it. Now slide the fence over to the board so it barely touches one end of the board.

4.Loosen the four fence alignment cap screws shown in

Figure 59.

5.Skew the fence left or right so it is parallel to the edge of the scrap piece.

6.While maintaining the skew, tighten the cap screws.

Figure 58. Example of blade lead.

Cap Screws

Figure 59. Fence alignment cap screws.

-46-

Page 47 Page 49
Image 48
Page 47 Page 49
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportControls and Features Blade Tracking Knob Adjusts and locks the blade trackingBlade Guide Lock Knob Locks the upper blade guides in place Blade Tension Knob Tensions the blade in gradual incrementsSafety Standard Machinery Safety InstructionsSafety Additional Safety for Bandsaws Power Supply Circuit Requirements for 110V PrewiredCircuit Requirements Full-Load Current RatingFor 110V Connection Prewired For 220V Connection Must Be RewiredGrounding Requirements Extension CordsSetup UnpackingInventory Inventory Figures QtyMachine Placement Cleaning Machine Setup Procedures AssemblyTo assemble the bandsaw, do these steps Installing the table onto Trunnion base Rear Fence Rail Dust Collection Recommended CFM at Dust PortBlade Tracking To center track the blade, do these stepsPower Connection Refer to Adjusting Blade Guide Bearings onAdditional Adjustments Test RunTo test run the machine, do these steps Adjusting Blade Guide Bearings on Page 24 for Tensioning BladeTo correctly tension the bandsaw blade, do these steps Adjusting Positive Stop To adjust the positive stop, do these stepsTools Needed Qty Aligning Table Taking measurements for aligning the table with the bladeAligning Miter Gauge Body To align the miter gauge body, do these stepsAdjusting Fence To align the fence with the miter slot, do these stepsAdjusting Blade Support Bearings To adjust the support bearings, do these stepsSupport bearing positioned Adjusting Blade Guide Bearings To adjust the blade guide bearings, do these stepsRotating the blade guide Bearings toward the blade Operations GeneralDisabling & Locking Switch Operation OverviewBasic Controls Cutting Overview Workpiece InspectionBasic Cutting Tips Cutting workpieces with minor WarpingAdjusting Guide Post To adjust the guide post, do these stepsTable Tilt To tilt the table, do these stepsRipping To make a rip cut, do these stepsCrosscutting To make a 90˚ crosscut, do these stepsResawing To resaw a workpiece, do these stepsCutting Curves Stacked Cuts⁄16 To complete a stacked cut, do these stepsBlade Speed To change the blade speed, do these stepsBlade Information Blade LengthBlade Width Tooth Style Tooth PitchBlade Care Blade BreakageBlade Changes To change the blade, do these stepsAccessories Bandsaw AccessoriesMaintenance Lubrication CleaningProtecting Table Service Redressing Rubber TiresTo redress the rubber tires, do these steps Belt Service Adjusting Belt TensionChecking Belt To tension the belt, do these stepsReplacing Belt To replace the belt, do these stepsShimming Table Items Needed QtyTo shim the table, do these steps Blade Lead Correcting Blade LeadTo skew the fence, do these steps Aligning Wheels Tool Needed QtySkew the table, do these steps Coplanar conditions Measuring the distance Wheel is out of adjustment Shimming a WheelElectrical Safety Instructions Wiring Diagram Color KEYW1706 Wiring Diagram Troubleshooting Problem Possible CauseParts Cabinet StandCabinet Stand Parts List Body Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents