Woodstock W1706 Cutting Curves, Stacked Cuts, ⁄16, To complete a stacked cut, do these steps

Page 37

Model W1706 (Mfg. Since 8/10)

Cutting Curves

When cutting curves, simultaneously feed and turn the stock carefully so that the blade follows the layout line without twisting. Use either a narrower blade or a blade with more TPI (teeth per inch), or make more relief cuts, to avoid having to back the workpiece away from the blade, especially if the curve is sharp.

Always make short cuts first, then proceed to the longer cuts. Relief cuts will also reduce the chance that the blade will be pinched or twisted. Relief cuts are cuts made through the waste portion of the workpiece and are stopped at the layout line. As you cut along the layout line, waste wood is released from the workpiece, alleviating any pressure on the back of the blade. Relief cuts also make backing the workpiece out easier once the saw blade has come to a stop, if needed.

NOTICE

The chart below displays blade widths and the corresponding minimum radii for those widths.

Width

Radius

1⁄8"

1⁄8"

3⁄16"

3⁄8"

1⁄4"

5⁄8"

3⁄8"

1⁜1⁄4"

1⁄2"

2⁜1⁄2"

5⁄8"

3⁜3⁄4"

3⁄4"

5⁜1⁄2"

Stacked Cuts

One of the benefits of a bandsaw is its ability to cut multiple copies of a particular shape by stacking a number of workpieces together (see Figure 45 for an example). Before making stacked cuts, ensure that both the table and the blade are properly adjusted to 90°. Otherwise, any error will be compounded.

To complete a stacked cut, do these steps:

1.Align your pieces from top to bottom to ensure that each piece has adequate scrap to provide a clean, unhampered cut.

2.Secure all the pieces together in a manner that will not interfere with the cutting. Hot glue on the edges works well, as do brad nails through the waste portion. (Be careful not to cut into the brads or you may break the blade!)

3.On the face of the top piece, lay out the shape you intend to cut.

4.Make relief cuts perpendicular to the outline of your intended shape in areas where changes in blade direction could strain the woodgrain or cause the blade kerf to bind.

5.Cut the stack of pieces as though you were cutting a single piece. Follow your layout line with the blade kerf on the waste side of your line.

Figure 45. Example of stacked cutting.

OPERATIONS

-35-

Page 36 Page 38
Image 37
Page 36 Page 38
Contents OWNERS MANUAL Page Contents Woodstock Technical Support IntroductionBlade Tracking Knob Adjusts and locks the blade tracking Controls and FeaturesBlade Guide Lock Knob Locks the upper blade guides in place Blade Tension Knob Tensions the blade in gradual incrementsStandard Machinery Safety Instructions SafetySafety Additional Safety for Bandsaws Circuit Requirements for 110V Prewired Power SupplyCircuit Requirements Full-Load Current RatingFor 220V Connection Must Be Rewired For 110V Connection PrewiredGrounding Requirements Extension CordsUnpacking SetupInventory Inventory Figures QtyMachine Placement Cleaning Machine Assembly Setup ProceduresTo assemble the bandsaw, do these steps Installing the table onto Trunnion base Rear Fence Rail Recommended CFM at Dust Port Dust CollectionTo center track the blade, do these steps Blade TrackingRefer to Adjusting Blade Guide Bearings on Power ConnectionTest Run Additional AdjustmentsTo test run the machine, do these steps Tensioning Blade Adjusting Blade Guide Bearings on Page 24 forTo correctly tension the bandsaw blade, do these steps To adjust the positive stop, do these steps Adjusting Positive StopTools Needed Qty Taking measurements for aligning the table with the blade Aligning TableTo align the miter gauge body, do these steps Aligning Miter Gauge BodyTo align the fence with the miter slot, do these steps Adjusting FenceTo adjust the support bearings, do these steps Adjusting Blade Support BearingsSupport bearing positioned To adjust the blade guide bearings, do these steps Adjusting Blade Guide BearingsRotating the blade guide Bearings toward the blade General OperationsOperation Overview Disabling & Locking SwitchBasic Controls Workpiece Inspection Cutting OverviewCutting workpieces with minor Warping Basic Cutting TipsTo adjust the guide post, do these steps Adjusting Guide PostTable Tilt To tilt the table, do these stepsTo make a rip cut, do these steps RippingTo make a 90˚ crosscut, do these steps CrosscuttingTo resaw a workpiece, do these steps ResawingStacked Cuts Cutting Curves⁄16 To complete a stacked cut, do these stepsTo change the blade speed, do these steps Blade SpeedBlade Length Blade InformationBlade Width Tooth Pitch Tooth StyleBlade Care Blade BreakageTo change the blade, do these steps Blade ChangesBandsaw Accessories AccessoriesLubrication Cleaning MaintenanceProtecting Table Redressing Rubber Tires ServiceTo redress the rubber tires, do these steps Adjusting Belt Tension Belt ServiceChecking Belt To tension the belt, do these stepsTo replace the belt, do these steps Replacing BeltItems Needed Qty Shimming TableTo shim the table, do these steps Correcting Blade Lead Blade LeadTo skew the fence, do these steps Tool Needed Qty Aligning WheelsSkew the table, do these steps Coplanar conditions Shimming a Wheel Measuring the distance Wheel is out of adjustmentWiring Diagram Color KEY Electrical Safety InstructionsW1706 Wiring Diagram Problem Possible Cause TroubleshootingCabinet Stand PartsBody Parts List Cabinet Stand Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents