Woodstock W1706 owner manual Resawing, To resaw a workpiece, do these steps

Page 36

Model W1706 (Mfg. Since 8/10)

Resawing

OPERATIONS

Resawing (see Figure 44 for an example) is the process of cutting a board into two or more thinner boards. The maximum board width that can be resawn is limited by the maximum cutting height of the bandsaw. Maximum cutting height for this bandsaw is 6".

The Model W1706 is capable of resawing, provided the saw is set up properly. Use common sense when resawing. Attempting to resaw too wide or too dense of a board may put excessive strain on the blade and cause it to break.

One of the most important considerations when resawing is blade selection. Use the widest blade possible when resawing—a wide blade cuts straighter and is less prone to blade lead (refer to Blade Lead on Page 46 for additional information). In most applications, a hook or a skip tooth style will be desirable.

Also, since most resawn lumber will be planed smooth, you should choose blades with fewer teeth-per-inch (from 3 to 6 TPI). While blades with fewer teeth-per-inch produce rougher cuts, these types of blades offer larger gullet capacities for clearing sawdust.

To resaw a workpiece, do these steps:

1.Verify that the bandsaw is setup properly and that the table is perpendicular to the blade.

2.Use the widest blade your bandsaw will accept. The blade must also be sharp and clean.

3.Set the fence to the desired width of cut and lock it in place.

Tip: You can also draw a reference line on the edge of the board, place the board against the fence, line up the reference line with the blade, then lock the fence in place.

4.Support the ends of the board if necessary.

5.Turn the bandsaw ON and wait for the blade to reach full speed.

6.Keeping even pressure against the fence and table with the workpiece, slowly feed it into the moving blade until the blade is completely through the workpiece.

When resawing thin pieces, a wandering blade (blade lead) can tear through the surface of the workpiece, exposing your hands to the blade teeth. ALWAYS keep your hands clear of the blade by using push blocks and push sticks when resawing.

Figure 44. Example of resawing.

-34-

Image 36
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportControls and Features Blade Tracking Knob Adjusts and locks the blade trackingBlade Guide Lock Knob Locks the upper blade guides in place Blade Tension Knob Tensions the blade in gradual incrementsSafety Standard Machinery Safety InstructionsSafety Additional Safety for Bandsaws Power Supply Circuit Requirements for 110V PrewiredCircuit Requirements Full-Load Current RatingFor 110V Connection Prewired For 220V Connection Must Be RewiredGrounding Requirements Extension CordsSetup UnpackingInventory Inventory Figures QtyMachine Placement Cleaning Machine Setup Procedures AssemblyTo assemble the bandsaw, do these steps Installing the table onto Trunnion base Rear Fence Rail Dust Collection Recommended CFM at Dust PortBlade Tracking To center track the blade, do these stepsPower Connection Refer to Adjusting Blade Guide Bearings onAdditional Adjustments Test RunTo test run the machine, do these steps Adjusting Blade Guide Bearings on Page 24 for Tensioning BladeTo correctly tension the bandsaw blade, do these steps Adjusting Positive Stop To adjust the positive stop, do these stepsTools Needed Qty Aligning Table Taking measurements for aligning the table with the bladeAligning Miter Gauge Body To align the miter gauge body, do these stepsAdjusting Fence To align the fence with the miter slot, do these stepsAdjusting Blade Support Bearings To adjust the support bearings, do these stepsSupport bearing positioned Adjusting Blade Guide Bearings To adjust the blade guide bearings, do these stepsRotating the blade guide Bearings toward the blade Operations GeneralDisabling & Locking Switch Operation OverviewBasic Controls Cutting Overview Workpiece InspectionBasic Cutting Tips Cutting workpieces with minor WarpingAdjusting Guide Post To adjust the guide post, do these stepsTable Tilt To tilt the table, do these stepsRipping To make a rip cut, do these stepsCrosscutting To make a 90˚ crosscut, do these stepsResawing To resaw a workpiece, do these stepsCutting Curves Stacked Cuts⁄16 To complete a stacked cut, do these stepsBlade Speed To change the blade speed, do these stepsBlade Information Blade LengthBlade Width Tooth Style Tooth PitchBlade Care Blade BreakageBlade Changes To change the blade, do these stepsAccessories Bandsaw AccessoriesMaintenance Lubrication CleaningProtecting Table Service Redressing Rubber TiresTo redress the rubber tires, do these steps Belt Service Adjusting Belt TensionChecking Belt To tension the belt, do these stepsReplacing Belt To replace the belt, do these stepsShimming Table Items Needed QtyTo shim the table, do these steps Blade Lead Correcting Blade LeadTo skew the fence, do these steps Aligning Wheels Tool Needed QtySkew the table, do these steps Coplanar conditions Measuring the distance Wheel is out of adjustment Shimming a WheelElectrical Safety Instructions Wiring Diagram Color KEYW1706 Wiring Diagram Troubleshooting Problem Possible CauseParts Cabinet StandCabinet Stand Parts List Body Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.