Woodstock W1706 owner manual Safety

Page 7

Model W1706 (Mfg. Since 8/10)

APPROVED OPERATION. Untrained operators can be seriously hurt by machinery. Only allow trained or properly supervised people to use machine. When machine is not being used, disconnect power, remove switch keys, or lock-out machine to prevent unauthorized use—especially around children. Make workshop kid proof!

ONLY USE AS INTENDED. Only use machine for its intended purpose. Never modify or alter machine for a purpose not intended by the manufacturer or serious injury may result!

USE RECOMMENDED ACCESSORIES. Consult this owner’s manual or the manufacturer for recommended accessories. Using improper accessories will increase the risk of serious injury.

CHILDREN & BYSTANDERS. Keep children and bystanders a safe distance away from work area. Stop using machine if children or bystanders become a distraction.

REMOVE ADJUSTING TOOLS. Never leave adjustment tools, chuck keys, wrenches, etc. in or on machine—especially near moving parts. Verify removal before starting!

SECURING WORKPIECE. When required, use clamps or vises to secure workpiece. A secured workpiece protects hands and frees both of them to operate the machine.

FEED DIRECTION. Unless otherwise noted, feed work against the rotation of blades or cutters. Feeding in the same direction of rotation may pull your hand into the cut.

GUARDS & COVERS. Guards and covers can protect you from accidental contact with moving parts or flying debris. Make sure they are properly installed, undamaged, and working correctly before using machine.

NEVER STAND ON MACHINE. Serious injury or accidental contact with cutting tool may occur if machine is tipped. Machine may be damaged.

STABLE MACHINE. Unexpected movement during operations greatly increases the risk of injury and loss of control. Verify machines are stable/secure and mobile bases (if used) are locked before starting.

FORCING MACHINERY. Do not force machine. It will do the job safer and better at the rate for which it was designed.

AWKWARD POSITIONS. Keep proper footing and balance at all times when operating machine. Do not overreach! Avoid awkward hand positions that make workpiece control difficult or increase the risk of accidental injury.

UNATTENDED OPERATION. Never leave machine running while unattended. Turn machine off and ensure all moving parts completely stop before walking away.

MAINTAIN WITH CARE. Follow all maintenance instructions and lubrication schedules to keep machine in good working condition. An improperly maintained machine may increase the risk of serious injury.

CHECK DAMAGED PARTS. Regularly inspect machine for damaged parts, loose bolts, mis-adjusted or mis-aligned parts, binding, or any other conditions that may affect safe operation. Always repair or replace damaged or mis-adjusted parts before operating machine.

EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties performing the intended operation, stop using the machine! Contact our Technical Support for help at (360) 734-3482.

SAFETY

-5-

Page 6 Page 8
Image 7
Page 6 Page 8
Contents OWNERS MANUAL Page Contents Woodstock Technical Support IntroductionBlade Tension Knob Tensions the blade in gradual increments Controls and FeaturesBlade Tracking Knob Adjusts and locks the blade tracking Blade Guide Lock Knob Locks the upper blade guides in placeStandard Machinery Safety Instructions SafetySafety Additional Safety for Bandsaws Full-Load Current Rating Power SupplyCircuit Requirements for 110V Prewired Circuit RequirementsExtension Cords For 110V Connection PrewiredFor 220V Connection Must Be Rewired Grounding RequirementsInventory Figures Qty SetupUnpacking InventoryMachine Placement Cleaning Machine Assembly Setup ProceduresTo assemble the bandsaw, do these steps Installing the table onto Trunnion base Rear Fence Rail Recommended CFM at Dust Port Dust CollectionTo center track the blade, do these steps Blade TrackingRefer to Adjusting Blade Guide Bearings on Power ConnectionTest Run Additional AdjustmentsTo test run the machine, do these steps Tensioning Blade Adjusting Blade Guide Bearings on Page 24 forTo correctly tension the bandsaw blade, do these steps To adjust the positive stop, do these steps Adjusting Positive StopTools Needed Qty Taking measurements for aligning the table with the blade Aligning TableTo align the miter gauge body, do these steps Aligning Miter Gauge BodyTo align the fence with the miter slot, do these steps Adjusting FenceTo adjust the support bearings, do these steps Adjusting Blade Support BearingsSupport bearing positioned To adjust the blade guide bearings, do these steps Adjusting Blade Guide BearingsRotating the blade guide Bearings toward the blade General OperationsOperation Overview Disabling & Locking SwitchBasic Controls Workpiece Inspection Cutting OverviewCutting workpieces with minor Warping Basic Cutting TipsTo tilt the table, do these steps Adjusting Guide PostTo adjust the guide post, do these steps Table TiltTo make a rip cut, do these steps RippingTo make a 90˚ crosscut, do these steps CrosscuttingTo resaw a workpiece, do these steps ResawingTo complete a stacked cut, do these steps Cutting CurvesStacked Cuts ⁄16To change the blade speed, do these steps Blade SpeedBlade Length Blade InformationBlade Width Blade Breakage Tooth StyleTooth Pitch Blade CareTo change the blade, do these steps Blade ChangesBandsaw Accessories AccessoriesLubrication Cleaning MaintenanceProtecting Table Redressing Rubber Tires ServiceTo redress the rubber tires, do these steps To tension the belt, do these steps Belt ServiceAdjusting Belt Tension Checking BeltTo replace the belt, do these steps Replacing BeltItems Needed Qty Shimming TableTo shim the table, do these steps Correcting Blade Lead Blade LeadTo skew the fence, do these steps Tool Needed Qty Aligning WheelsSkew the table, do these steps Coplanar conditions Shimming a Wheel Measuring the distance Wheel is out of adjustmentWiring Diagram Color KEY Electrical Safety InstructionsW1706 Wiring Diagram Problem Possible Cause TroubleshootingCabinet Stand PartsBody Parts List Cabinet Stand Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents