Woodstock W1706 owner manual Shimming Table, Items Needed Qty, To shim the table, do these steps

Page 47

Model W1706 (Mfg. Since 8/10)

Shimming Table

To ensure accuracy when cutting stacked workpieces or circles, the table should be 90° to the back of the blade, as illustrated in Figure 56. If the table is not perpendicular to the back of the blade, the table will need to be shimmed.

Items Needed

Qty

Wrench or Socket 10mm

1

Machinist's Square

1

Metal Shims

As Needed

To shim the table, do these steps:

 

1.Make sure that the blade is tracking properly and that it is correctly tensioned.

2.DISCONNECT BANDSAW FROM POWER!

3.Bring the table to 0° tilt, then place the machinist's square flat on the table and against the back of the blade.

—If there is not a gap between the square and the blade, no further adjustments need to be made.

—If there is a gap between the square and the blade, continue with Step 4.

4.Loosen the six trunnion bolts that secure the trunnions to the table (see Figure 57).

5.Place shim stock between the table and the two trunnions to shim the table in the desired direction.

Another way to shim the table is to add washers between the table and the trunnion. Electrical washers are a good choice for this procedure because they are very thin and will allow for fine adjustment.

6.Check, and if necessary, align the table (refer to

Page 19).

Blade

Square

Table

Figure 56. Checking if the table is

perpendicular to the back of the blade.

Trunnion

Bolt

Figure 57. Location of trunnion bolt

(1 of 6).

SERVICE

-45-

Page 46 Page 48
Image 47
Page 46 Page 48
Contents OWNERS MANUAL Page Contents Woodstock Technical Support IntroductionBlade Tension Knob Tensions the blade in gradual increments Controls and FeaturesBlade Tracking Knob Adjusts and locks the blade tracking Blade Guide Lock Knob Locks the upper blade guides in placeStandard Machinery Safety Instructions SafetySafety Additional Safety for Bandsaws Full-Load Current Rating Power SupplyCircuit Requirements for 110V Prewired Circuit RequirementsExtension Cords For 110V Connection PrewiredFor 220V Connection Must Be Rewired Grounding RequirementsInventory Figures Qty SetupUnpacking InventoryMachine Placement Cleaning Machine To assemble the bandsaw, do these steps Setup ProceduresAssembly Installing the table onto Trunnion base Rear Fence Rail Recommended CFM at Dust Port Dust CollectionTo center track the blade, do these steps Blade TrackingRefer to Adjusting Blade Guide Bearings on Power ConnectionTo test run the machine, do these steps Additional AdjustmentsTest Run To correctly tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings on Page 24 forTensioning Blade Tools Needed Qty Adjusting Positive StopTo adjust the positive stop, do these steps Taking measurements for aligning the table with the blade Aligning TableTo align the miter gauge body, do these steps Aligning Miter Gauge BodyTo align the fence with the miter slot, do these steps Adjusting FenceTo adjust the support bearings, do these steps Adjusting Blade Support BearingsSupport bearing positioned To adjust the blade guide bearings, do these steps Adjusting Blade Guide BearingsRotating the blade guide Bearings toward the blade General OperationsOperation Overview Disabling & Locking SwitchBasic Controls Workpiece Inspection Cutting OverviewCutting workpieces with minor Warping Basic Cutting TipsTo tilt the table, do these steps Adjusting Guide PostTo adjust the guide post, do these steps Table TiltTo make a rip cut, do these steps RippingTo make a 90˚ crosscut, do these steps CrosscuttingTo resaw a workpiece, do these steps ResawingTo complete a stacked cut, do these steps Cutting CurvesStacked Cuts ⁄16To change the blade speed, do these steps Blade SpeedBlade Width Blade InformationBlade Length Blade Breakage Tooth StyleTooth Pitch Blade CareTo change the blade, do these steps Blade ChangesBandsaw Accessories AccessoriesProtecting Table MaintenanceLubrication Cleaning To redress the rubber tires, do these steps ServiceRedressing Rubber Tires To tension the belt, do these steps Belt ServiceAdjusting Belt Tension Checking BeltTo replace the belt, do these steps Replacing BeltTo shim the table, do these steps Shimming TableItems Needed Qty To skew the fence, do these steps Blade LeadCorrecting Blade Lead Skew the table, do these steps Aligning WheelsTool Needed Qty Coplanar conditions Shimming a Wheel Measuring the distance Wheel is out of adjustmentWiring Diagram Color KEY Electrical Safety InstructionsW1706 Wiring Diagram Problem Possible Cause TroubleshootingCabinet Stand PartsBody Parts List Cabinet Stand Parts ListBody Wheel Tire Fence & Miter Gauge Fence & Miter Gauge Parts List Model W1706 Mfg. Since 8/10 Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools

W1706 specifications

The Woodstock W1706 is a versatile and robust woodworking machine designed to cater to both professional carpenters and woodworking enthusiasts. Renowned for its exceptional build quality and innovative features, the W1706 stands out in the crowded market of woodshop equipment.

At its core, the W1706 is a heavy-duty table saw, offering a powerful 1.5 HP motor that delivers reliable performance even under demanding load conditions. This motor is designed to provide efficient cutting power while maintaining low noise levels, ensuring a pleasant working environment. The saw can handle a variety of materials ranging from softwoods to hardwoods, making it suitable for an extensive range of applications.

One of the key characteristics of the W1706 is its precision-engineered cast iron table. This large, flat surface offers excellent stability and minimizes vibrations during operation, allowing for accurate cuts. The integrated T-slot miter gauge adds to the versatility, enabling users to make precise crosscuts and angled cuts with ease. Additionally, the table is equipped with an extendable infeed and outfeed support, facilitating the handling of larger workpieces.

Safety features are paramount in the design of the W1706. It includes a riving knife that helps prevent kickback, a crucial aspect of safe woodworking practice. The blade guard provides further protection, allowing users to operate the machine with a peace of mind. Moreover, the push stick and emergency stop button enhance safety, ensuring that operators can quickly disengage the machine if necessary.

The W1706 is also designed with user convenience in mind. Its easy-to-read scaled fence provides quick adjustments for different cutting widths, promoting efficiency without compromising accuracy. The saw is fitted with a dust collection port that connects to a vacuum system, significantly reducing mess and ensuring a clean workspace.

In addition to its impressive features, the Woodstock W1706 is built for longevity. Constructed with durable materials, it is designed to withstand the rigors of daily use. With proper maintenance, users can expect this machine to serve them well for many years.

In summary, the Woodstock W1706 is a top-of-the-line tabletop saw that excels in performance, safety, and user convenience. Its powerful motor, precision engineering, safety features, and durable construction make it an ideal choice for anyone looking to elevate their woodworking projects to the next level. Whether for professional use or serious hobbyists, the W1706 is a reliable tool that truly embodies quality craftsmanship.
Top Page Image Contents