Woodstock W1814 manual 8jj\dYcp, KfXjj\dYc\k\af`ek\i#fk\j\jk\gj1

Page 16

N(/(+Fne\ijDXelXcD]^%('&'/"

8jj\dYcp

KfXjj\dYc\k_\af`ek\i#[fk_\j\jk\gj1

(% DISCONNECT JOINTER FROM POWER SOURCE!

)% Use two of the included cap screws and lock washers to attach the fence support to the jointer bed, as shown in =`^li\12.

Cap Screws

		Fence
Jointer Bed		Support

J<KLG

*% Insert the locking plate assembly into the fence support, positioning it so the two pins are against the bottom edge of the fence support, as shown in =`^li\13.

=`^li\12. Attaching the fence support to

the bed assembly.

Locking Plate

Assembly

Locking

Plate Pins

+% Secure the locking plate in position with the fence sliding handle, as shown in =`^li\14.

-14-

=`^li\13. Inserting the locking plate.

Locking Plate

Assembly

Fence Sliding

Handle

=`^li\14. Securing the locking plate assembly with the fence sliding handle.

Image 16

Contents DLCGHB6CJ6A Page KXYc\ffek\ekj @EKIFLK@FE@EKIFLK@FE NffjkfZbK\Ze`ZXcJlggfikB68=C HE886IDCH FekifcjXe=\Xkli\j J8=KP JkXeXiJX\kp@ejkilZk`fejD8BJLIL8IJ8I@EGC88ENFIBFIIKCP9=FILJ@ED8?@EIP% `k`feXcJX\kp@ejkilZk`fejfiAf`ek\ij 8mf``eGfk\ek`Xc@eali`\j =`li\.%Never joint end grainFg\iXk`fe Ok\ej`fefij\Zki`ZXcJg\Z``ZXk`fej =`li\8% 5-15 plug and receptacle@k\djE\\\fiJ\klg LegXZb`eSee GX\ @em\ekfip Af`ek\i9fofek\ekj1=`li\8 & 9?XinXi\EfkJfne Gfn\i dljk efk Y\ Zfee\Zk\ kf dXZ`e\li`ej\klgDXZ`e\GcXZ\d\ek \Xe`eDXZ`e\\eZDflek`e 8jj\dYcp KfXjj\dYc\k\af`ek\i#fk\j\jk\gj1=`li\17% Fence BracketFence Support Dovetail=`li\ \Zb`e&8aljk`eBe`\ ?\`kKfXaljkk\be`\\`k#fk\j\jk\gj1 Ljkfcc\Zk`fe =`li\22% Checking each end of the knife With a straightedge\jkIle Kfk\jkilepfliaf`ek\i#fk\j\jk\gj1FGI8K@FEJ \e\iXc9Xj`Zfekifcj ?\i\Xi\jfd\ilc\jkffccfnn\eZffj`eXe af`ek`ejkfZb1 =`li\.% Correct setting for grain Alignment 10 Min⁄ 2 Min JhlXi`eJkfZb JliXZ\GcXe`e =`li\*,%Illustration of surface planing Results\Af`ek`e Kf\\af`ekfek\af`ek\i#fk\j\jk\gj1Read and understandJ8=KP, beginning on GX\ RepeatJk\g. until the entire edge is flat\m\clkk`e KfY\m\cZlkfek\af`ek\i#fk\j\jk\gj1\Xe`e $9\ckjClYi`ZXk`fe `cp\ZbKfj\kk\0²jkfg#fk\j\jk\gj1 Limit Plate Limit Block Rear SlotBlock Set ScrewKfj\kk\`enXi+,²jkfg#fk\j\jk\gj1 \gcXZ`eBe`m\j Kfj\kk\flknXi+,²jkfg#fk\j\jk\gj1$9\ckI\gcXZ\d\ek Kfi\gcXZ\k\XeY\ck#fk\j\jk\gj1Dfkfi9iljI\gcXZ\d\ek Kfi\gcXZ\dfkfiYilj\j#fk\j\jk\gj1N`i`e`XiXd G8CJN@K? m`\n\ifdY\`eKiflYc\jffk`e Dfkfic\Zki`ZXcLkk`e G8IKJ JkXeGXikjC`jk DescriptionCXY\cj&fjd\k`ZGXikj G8IKJ NXiiXekpI\`jkiXk`fe 20+ Years$30,000-$39,000 $40,000-$49,000 Modeltec Shop Notes Other Old House Journal Shotgun NewsPlace Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah