Woodstock W1814 manual JliXZ\GcXe`e, =`li\*,%Illustration of surface planing Results

N(/(+Fne\ijDXelXcD]^%('&'/"

Jli]XZ\GcXe`e^

The purpose of surface planing on the jointer is to make one flat face on a piece of stock (see =`^li\j*+ & *,) to prepare it for surface planing on a thickness planer.

EFK@:<

@] pfl Xi\ efk \og\i`\eZ\[ n`k_ X af`ek\i# j\k k_\ [\gk_ f] Zlk kf '# Xe[ giXZk`Z\ ]\\[`e^ k_\ nfibg`\Z\ XZifjj k_\ kXYc\j Xj [\jZi`Y\[ Y\cfn% K_`j gifZ\[li\ n`cc Y\kk\i gi\gXi\ pfl ]fi k_\ XZklXcfg\iXk`fe%

Kfjli]XZ\gcXe\fek_\af`ek\i#[fk_\j\jk\gj1

(% Read and understand J8=<KP, beginning onGX^\,.

)% Make sure your stock has been inspected for dangerous conditions as described in the JkfZb @ejg\Zk`feI\hl`i\d\ekjinstructions, beginning on GX^\)(%

*% Set the cutting depth for your operation. (We suggest 1⁄32" for surface planing, using a more shallow depth for hard wood species or for wide stock.)

+% Make sure your fence is set to 90˚.

,% If your workpiece is cupped (warped), place it so the concave side is face down on the surface of the infeed table.

-%Start the jointer.

.% With a push block in each hand, press the workpiece against the table and fence with firm pressure, and feed the workpiece over the cutterhead (=`^li\*+).

Efk\1 N_\epflic\X[`e^_Xe[n`k_glj_YcfZb ^\kj n`k_`e+f]k_\Zlkk\i_\X[#c`]k`klgXe[fm\ik_\ Zlkk\i_\X[#Xe[gcXZ\k_\glj_YcfZbfek_\gfi$ k`fef]k_\nfibg`\Z\k_Xk`jfek_\flk]\\[kXYc\% Efn#]fZljpfligi\jjli\fek_\flk]\\[\e[f]k_\ nfibg`\Z\n_`c\]\\[`e^#Xe[i\g\Xkk_\jXd\XZk`fe n`k_pflikiX`c`e^_Xe[n_\e`k^\kjn`k_`e+f]k_\ Zlkk\i_\X[%Kfb\\gpfli_Xe[jjX]\#;FEFKc\k k_\d^\kZcfj\ik_Xe+]ifdk_\Zlkk\i_\X[n_\e`k `jdfm`e^

/% Repeat Jk\g. until the entire surface is flat.

-23-

=`^li\*+% Typical surface planing

operation.

Portion

Removed With

Jointer

=`^li\*,%Illustration of surface planing

results.

=X`cli\ kf lj\ glj_ YcfZbj n_\e jli$ ]XZ\gcXe`e^dXpi\jlck`eZlkk\i_\X[ ZfekXZk#n_`Z_n`ccZXlj\j\i`fljg\i$ jfeXc `ealip% 8cnXpj lj\ glj_ YcfZbj kf gifk\Zk pfli _Xe[j n_\e jli]XZ\ gcXe`e^fek_\af`ek\i%

FG<I8K@FEJ