Emerson VSSG, VSG manual Coalescing Filter Replacement, Maintenance/Service, Centering Strap

Page 66

Coalescing Filter

Section 5 • Maintenance/Service

	Oil Separator Vessel
	Oil Separator
	Manhole Cover
		Pipe Stub
	Coalescing Filter	Hold-Down Rod
	Centering Strap
	Flat Washer	3/4 in. O.D.
	Flat Washer	3/4 in. O.D.
	Flat Washer	Tubing, 6 ft. long
	Nuts
	Figure 5-6. Oil Separator Manhole Cover and Coalescing Filter Assembly

Coalescing Filter Replacement

2.If required, install lifting eyes on oil separator man- hole cover, see Figure 5-6.

WARNING

Use appropriate lifting devices and additional personnel when lifting heavy components. Ensure lifting devices are capable of lifting the weight of the component. Use lifting points (i.e. bolt holes designated for lifting eye bolts) that are provided on the component. Failure to comply may result in

serious injury.

WARNING

Avoid skin contact with any condensate or oil. Wear rubber gloves and a face shield when working with condensate or oil. Failure to comply may result in serious injury or death.

NOTE

3.Secure appropriate lifting device to oil separator manhole cover.

4.Remove all bolts except top four bolts securing oil separator manhole cover to oil separator vessel.

5.Adjust lifting device as needed to hold weight of oil separator manhole cover.

6.Remove remaining four bolts and oil separator manhole cover from oil separator vessel.

7.Remove nuts, ﬂat washer and cover plate securing coalescing oil ﬁlter to hold-down rod.

8.With assistance of second person, remove coalesc- ing ﬁlter from oil separator vessel.

9.Repeat steps 7 and 8 to remove additional coalesc- ing ﬁlters, as required.

For coalescing oil ﬁlters (11-7/8 in. O.D.), a tubing (3/4 in. O.D. x 6 ft. long ) can be used to aid in removal and installation of the element.

REMOVAL

1.Isolate the compressor unit, see Compressor Unit Isolation procedure.

INSTALLATION

10.Install tubing over hold-down rod. Position tubing as far back as possible.

11.With assistance of second person, position coalesc- ing element over tubing and through hole of cen- tering strap.

12.Push coalescing ﬁlter into vessel until fully seated

5 – 8

VSG/VSSG • Installation, Operation and Maintenance Manual •Vilter/Emerson • 35391SSG

Image 66

Contents Installation, operation & maintenance manual VSG/VSSG compressor unitPage VSG/VSSG Standard Vilter Warranty Statement Important Message READ CAREFULLY BEFORE INSTALLING AND STARTING YOUR COMPRESSORVilter Manufacturing LLC Section Title Table of ContentsSection 3 Installation Section 1 General InformationSection Number Section 5 Maintenance/ServiceSection 6 Troubleshooting Section 4 OperationAppendices Section 7 Warranty and PartsList of Tables and Figures Table/FigureFigure 3-12. Installation of Coolers - Next to Buildling Section 1 General Information How To Use This Manual Section 1 General Information Gas Compressor Unit Model Designations Figure 1-1. Gas Compressor Unit Model DesignationSection 1 General Information System Unit Identiﬁcation Section 1 General Information Compressor Unit Component IdentiﬁcationFigure 1-2. Gas Compressor Unit Components 1 of Figure 1-2. Gas Compressor Unit Components 2 of Section 1 General Information Component Identiﬁcation Continued Figure 1-2. Gas Compressor Unit Components 3 ofSection 1 General Information Piping & Identiﬁcation Component Tags Symbols and Identiﬁcations Position Transmitter3-Way Thermostatic Valve High Side Float Valve Steady-Mount Bulb & Capillary 1 - 10 / Blank Oil Life and Oil Flow Section 2 Theory of OperationGas Flow Figure 2-1. Gas Compressor Unit P&IDRTDs and Pressure Transducers Control SystemThis is a continuous cycle Rigging and Lifting of Compressor Unit Section 3 InstallationDelivery Inspection Figure 3-1. Rigging and Lifting PointsLong Term Storage Recommendations The following are recommendations regarding long term storageCompressor Unit Inspections Prior to Storage or Installation Recommended Onsite ToolsAIR COOLED OIL COOLERS LONG TERM STORAGE LOG Compressor has been placed in operation as ofConsiderations Prior to Starting FoundationFoundation Materials Building the FoundationCompressor Unit Installation of both Check the ability of the soil to carry the loadLeveling and Grouting recommendations for setting, precautions, mixing, andAdditional Information Codes and Standards LEVEL Figure 3-6. Housekeeping Pad Dimension Detail - Top View2 - # CLOSED TIES CENTER LINE 5 - # 6 VERT COMPRESSOR UNIT HOUSEKEEPING PADSPiping 010Ä5*4+0- 214176 4%1//0&& 14 175-2+0 10%46 $#5Fz lbf Table 3-2. Maximum Allowable Flange LoadsNozzle Dia. in Fy lbfONE FAN DIAMETER NOT PREFERRED HOT AIR RECIRCULATION Figure 3-14. Cooler Placement and Spacing Figure 3-13. Discharge Elevation of CoolersPREFERRED Unit Oil Charging and Priming Pressure TestingInitial Oil Charging Using Non -Vilter Oils Do not hydro test compressur unit. Failure to complyNormal Operating Level Maximum NON-Operating Level Minimum Operating LevelBypass Valve CLOSE OIL MIXINGSUCTION INLET OPEN VALVEPriming Remote Oil Cooler and Piping Section 3 InstallationInitial Oil Charging REMOTESUCTION INLET OIL FILTER OPENMOTOR Section 3 Installation Pre Start-Up Pre Start-Up Checklist15. Verify that all valves are in the open position Section 3 Installation Start-Up Oil Inspection Section 4 OperationOperation Dual Oil FiltersStarting, Stopping and Restarting the Compressor Starting Control System CalibrationStopping/Restarting Calibrate Slide Valve ActuatorsFigure 4-2. Actuator Assembly Section 4 Operation Figure 4-4. Slide Valve Calibration Screen Compact Logix PLC Figure 4-5. Photo-chopperTable 4-1. Command Shaft Rotation Speciﬁcations Angle/Slide TravelCapacity Oil Temperature Control Valve Oil Mixing Valve Operation 18. Press the “Set Max” buttonFail Position Purging with Dry Nitrogen 10. Close discharge bleed valve while still purging Purging with Dry Gas Pressure IndicatorOIL SEPARATOR Section 4 Operation Figure 4-12. Suction Bypass Valve and Equalizing Solenoid Suction Oil Figure 4-13. Suction Oil Charging ValveCoalescing Oil Return Line Setup Unit Table 5-1. Maintenance/Service ScheduleOil Circuit ControlMaintaining Proper Operation Section 5 Maintenance/ServiceMaintenance/Service Compressor Unit Isolation forCompressor Unit Leak Check sample for analysis. For an example, see Figure 5-2. Fill Oil System Components Oil SamplingUse Vilter Oil Analysis Kit VPN 3097A to collect an oil Send samples immediately to the oil analysis lab afterOil Charging Dual Oil Filter Assembly Oil Filter ReplacementSingle Oil Filter Assembly Oil DrainingVent Valve Drain Valve Inlet Shut-Off Valves Coalescing Filter Replacement Coalescing FilterCentering Strap Oil Pump Strainer View From Back of Oil Pump StrainerDrive Coupling Form-Flex BPU Hub Installation Table 5-3. Shaft and Hub DistancesSize Drive Center Member Installation and Alignment 17. Install set screw in hub cap to secure key in keyway of shaftTable 5-5. Disc Pack Installation Torque Speciﬁcations Table 5-4. Hub Clamp Bolt and Set Screw Torque SpeciﬁcationsAngular Alignment Drive Coupling Type C Sure-Flex Replacement Drive Coupling Form-Flex BPU Center Member and Hub RemovalCompressor Replacement Table 5-6. Clamping Bolts and Set Screw Torque SpeciﬁcationsLock Washer Compressor Shaft Bearing Float Inspections Figure 5-11. Bearing Axial Float InspectionFigure 5-12. Bearing Radial Float Inspection Gate Rotor Float and Gate Rotor Bearing Float InspectionTable 5-7. Maximum Bearing Float Figure 5-13. Gate Rotor FloatApplied Force Rigidly attach dial indicator Use bolt for fulcurm Table 5-8. Gate Rotor FloatFigure 5-14. Gate Rotor Bearing Float Gate rotor bearing float being measuredSection 5 Maintenance/Service Gate Rotor and Support Clearance Figure 5-15. Gate Rotor and Support Clearance - Minimum ClearancesGate Rotor Support Gate Rotor Figure 5-16. Gate Rotor and Support Clearance - MeasuringGate Rotor Support Gate Rotor Gate Rotor Support Gate Rotor Straight Edge Straight Edge Straight EdgeGate Rotor Assembly Replacement All VSG & VSSG Compressors Except VSG 301-701 CompressorsTable 5-9. Gate Rotor Tool Sets Figure 5-17. Gate Rotor Assembly Removal and Tools Figure 5-18. Gate Rotor Assembly RemovalFigure 5-19. Gate Rotor Assembly and Tools Figure 5-20. Gate Rotor and Shelf ClearanceGate Rotor Assembly Replacement VSG 301-701 Compressors ONLY Figure 5-21. Gate Rotor Assembly BreakdownFigure 5-23. Gate Rotor and Shelf Clearance Figure 5-22. Gate Rotor Thrust BearingGate Rotor Disassembly Figure 5-25. Gate Rotor Blade InstallationFigure 5-24. Gate Rotor Blade Assembly Figure 5-27. Thrust Bearing Installation Figure 5-26. Gate Rotor Thrust BearingSlide Valve Actuator Assembly Replacement Figure 5-28. Roller Bearing AssemblyCommand Shaft Assembly Replacement Command Shaft Seal ReplacementFigure 5-29. Command Shaft Seal Figure 5-30. Command Shaft Seal Installation Solution Section 6 TroubleshootingProblem Table 6-1. Slide Valve Actuator Troubleshooting Guide 1 ofTable 6-1. Slide Valve Actuator Troubleshooting Guide 2 of Flash Pattern MeaningTable 6-2. Slide Valve Actuator LED Blink Codes* 1 of calibrate the actuator. If this error has occurred and the cause was er before the calibration procedure was completed. The actuatorwill not move while this error code is displayed. To clear the error not the loss of 24V power during calibration, possible causes areTable 6-3. Troubleshooting Guide - General Problems & Solutions 1 of Table 6-3. Troubleshooting Guide - General Problems & Solutions 2 of Table 6-3. Troubleshooting Guide - General Problems & Solutions 3 of 6 - 8 / Blank On Site Service Support Section 7 Warranty and PartsWarranty Claim Processing Warranty does not cover labor and extraneous expensesRemanufactured Gas Bare Shaft Compressor Process Request a “VSG Single Screw Compressor Rebuild Form”Appendix A Torque Specifications Torque Specifications ft-lbsTorque Specifications for 17-4 Stainless Steel Fasteners ft-lbs Appendix B Motor Compressor - General Storage Instructions PRODUCT ANALYSIS REPORT Appendix C Oil Analysis ReportEvaluation No Action RequiredAppendix D Recommended Header Piping Appendix E Recommended Remote Air Cooled Oil Cooler Piping OUTLET ON TOPINLET ON BOTTOM Blank