Videk 2030 Batch Operation, Introduction, RS232 Considerations, RS232 Batch Cable-Detect Default

Page 12

1.5 - Batch Operation

1.5.1 - Introduction

Batch data storage and data transfer are controlled by the resident JavaScript application on your VS 2030 reader. Under the default factory settings, batch mode is enabled.

When the VS 2030 is NOT connected to a host PC or other device, it will store reading data. Then when subsequently connected to a host device the VS 2030 will automatically upload all of the read data and erase it from its memory.

MAKE SURE that when the VS 2030 is connected to the host device that the appropriate application is open and active on the host device. If not, the read data will be lost.

1.5.2 - RS232 Considerations

In RS232 Batch Cable-Detect mode, the VS 2030 will detect if it is connected to a powered serial cable, and will send the data. If a powered serial cable is not connected or if the power adapter is not connected to the serial cable, the VS 2030 will buffer the data. When the VS 2030 is then connected to a powered serial cable, the data will automatically upload and be erased from the VS 2030 memory.

In RS232 Cabled - No Power mode, the VS 2030 will behave as if it is always connected even though the serial cable is disconnected or the power adapter is unplugged. Scanned data will be sent, regardless of connection status. Data scanned in Cabled mode will be lost if the VS 2030 is not connected to the serial cable. It will not buffer the data, unless Send & Store mode has been enabled.

Important Note: If you are in RS232 Cabled-No Power mode, when you place a unit in a charger the reader will behave as if it is being cabled, and download the data. THE DATA WILL BE ERASED FROM MEMORY. To disable this feature, scan the RS232 Cable - Detect code.

RS232 Batch Cable-Detect - Default

RS232 Cabled - No Power

NOTE: After making changes to settings by scanning the setup/configuration codes, always scan the “SAVE SETTINGS” code at the bottom of the page to assure that the new settings will be saved in the VS 2030 memory for use the next time the reader is powered on.

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 -

Image 12

Contents Part Number K11020, Rev. E, August 3 Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents VS 2030 Programming Symbology Settings UPC/EAN/JANAppendix a Reader Specifications Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionRS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 ConsiderationsCabled Operation IntroductionUSB Cable Installation Guide USB Keyboard Default USB Downloader USB Virtual COM 1 Way ModeRS232 Cable Installation Guide RS232 One Way Mode Save SettingsMode RS232 One Way Mode Baud RateData Bits Data Bits Default Stop Bits Default1200 2400 4800 9600 19200 38400 Default 115200 Even Odd None DefaultCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultReader Feedback Guide RS232To read a symbol with the VS Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Read Codes with Both Imagers Default Left Trigger Optimization MatrixLeft Trigger Programming Read with Near-Field Imager onlyRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger ProgrammingFar Field Only On Off Default Continuous Trigger Optimization MatrixContinuous Scan Both Near & Far Field OnContinuous Scan Settings Motion Detection Scan SettingsSeconds Default VS 2030 Programming Symbology Settings Aztec Symbology Codabar SymbologyCodablock F Symbology Code 11 SymbologyCode 39 Symbology Codablock F On Codablock F Off DefaultCode 93 Symbology Code 128 SymbologyCode 93 On Default Code 93 Off Sample Trioptic CodeComposite Symbologies Data Matrix SymbologyComposite On Composite Off Default Interleaved 2 of 5 Symbology Maxicode SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPharmacode Postal Symbologies Advanced Postal Symbologies UK ID Tag On Default UK ID Tag OffQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Volume and Vibration Settings Off Default Low MediumCode Readability Index Vibrate On / Beep On Vibrate On / Beep OffBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader Settings Lock Reader Settings LockedReader ID and Firmware Version Reader ID and FirmwareTime Stamp Settings US English Default US English LeadingKeyboard Support No Leading French GermanAdvanced Decode Performance Enable Continuous Illumination Continuous IlluminationSet Targeting Zone Tolerances 100 125Windowing Medium Code Windowing Small Code WindowingLarge 2-Dimensional Codes 640 x 640 pixels VGA & Megapixel Settings Codes Enable Sxga 1024 xEnable VGA 640 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Prefix Settings Suffix SettingsPrefix Comma Prefix Space Erase Prefix and Suffix Settings Reader Text CommandsReader Text Commands On Erase Prefix & Suffix DataVS 2030 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationWarranty Limited WarrantyTerms of Warranty Warranty Coverage and ProcedureVS 2030 Accessories Troubleshooting GeneralVS 2030 Maintenance Cleaning the VS 2030 WindowTechnical Support and Returns Appendix a Reader Specifications Physical Characteristics Performance CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Default Settings Symbology DefaultsControl Setting Defaults RS-232 Interface Setting Defaults Batch Mode Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Global All Trigger Optimization and Settings Left Trigger Optimization and SettingsRight Trigger Optimization and Settings Handle Trigger Optimization and SettingsContinous Trigger Optimization and Settings SymbologiesCode 39 On Default Symbol Readability Index Reader FeedbackBacklight Settings Laser SettingsIllumination Settings Keypad VolumeReader Text Commands Reader Settings LockedMiscellaneous Settings Targeting Zone TolerancesBatch Log Only Mode Batch Send & Log Mode VS 2030 Programming CodesSuffix Tab USB Keyboard Mode only RS232 Interface Baud Rate Suffix Erase/None Default RS232 Interface Baud RateRS232 Interface Baud RateVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable Allow ALL Data Matrix Codes Default 5 with Control Character StrippedAllow only Programming Data Matirx Codes Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off QR Code On QR Code Off Default QR Code Enable QR Code Inverse On QR & Micro QR Code OnRSS Expanded On UPC Off UPC Extension Off Vibrate On Beep On Vibrate On Beep Off Backlight Intensity LowBacklight Intensity High Backlight OffDefault Reader Power Off 1 Hour Keypad Volume HighMirroring Off Default Continous IlluminationUS English ctrl + char Lockout Link Mode