Videk 2030 manual Removing and Attaching Handle

Page 23

1.11 - Removing and Attaching Handle

The battery-handle must be attached to the VisionSensor 2030 for proper operation.

The battery automatically charges every time the USB interface is attached to the VisionSensor 2030 and the host PC is powered up.

Attaching the Battery Handle

Step 1: Begin assembly by inserting the tab at the back of the handle into the reader’s battery compartment.

Step 2: Push the reader forward snugly against the handle.

Step 3: Snap the reader to the handle. Assembly is complete.

Note: To further secure the reader to the handle use the two screws included in shipment (optional). The screws are located on the underside of the reader.

Removing Reader from Handle

First remove the two screws (if used) from the underside of the handle. Next, release the battery compartment clip as shown, then remove the reader from the handle.

An optional battery charger cradle is available.

Please contact Videk for additional information.

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 17

Image 23

Contents Part Number K11020, Rev. E, August 3 Laser/LED Radiation Statement of Agency ComplianceSave Settings Table of Contents UPC/EAN/JAN VS 2030 Programming Symbology Settings Appendix a Reader Specifications Getting Started Introduction Unpacking Powering On/Off ReaderDescription of Button Function Keypad/Icon OverviewIcon Description Power IconsRS232 Considerations RS232 Batch Cable-Detect DefaultBatch Operation IntroductionIntroduction Cabled OperationUSB Cable Installation Guide USB Virtual COM 1 Way Mode USB Keyboard Default USB DownloaderBaud Rate RS232 Cable Installation GuideRS232 One Way Mode Save Settings Mode RS232 One Way ModeEven Odd None Default Data Bits Data Bits DefaultStop Bits Default 1200 2400 4800 9600 19200 38400 Default 115200Cabled 2 hours Cabled Always Default Cabled Reader Time Out SettingsRS232 Reader Feedback GuideTargeting and Reading Techniques To read a symbol with the VSImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming DOT IntroductionGlobal Trigger Optimization Matrix Read with Near-Field Imager only Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Left Trigger ProgrammingRead Code with Near-Field Imager only Right Trigger Optimization MatrixRight Trigger Programming Handle Trigger Programming Handle Optimization MatrixBoth Near & Far Field On Far Field Only On Off DefaultContinuous Trigger Optimization Matrix Continuous ScanSeconds Default Continuous Scan SettingsMotion Detection Scan Settings VS 2030 Programming Symbology Settings Codabar Symbology Aztec SymbologyCodablock F On Codablock F Off Default Codablock F SymbologyCode 11 Symbology Code 39 SymbologySample Trioptic Code Code 93 SymbologyCode 128 Symbology Code 93 On Default Code 93 OffComposite On Composite Off Default Composite SymbologiesData Matrix Symbology Maxicode Symbology Interleaved 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy Matrix 2 of 5 SymbologyMSI Plessy Symbology Pharmacode NEC 2 of 5 SymbologyNEC 2 of 5 On NEC 2 of 5 Off Default Postal Symbologies UK ID Tag On Default UK ID Tag Off Advanced Postal SymbologiesRSS Symbology QR Code SymbologyUPC/EAN/JAN Telepen SymbologyReader Feedback and Special Settings Vibrate On / Beep On Vibrate On / Beep Off Volume and Vibration SettingsOff Default Low Medium Code Readability IndexLow Med Default High Backlight Intensity SettingsReadability Index Output Disable Reader Power Off Settings Backlight Timeout SettingsLaser Settings Reader ID and Firmware Reader Settings LockReader Settings Locked Reader ID and Firmware VersionNo Leading French German Time Stamp SettingsUS English Default US English Leading Keyboard SupportAdvanced Decode Performance 100 125 Enable Continuous IlluminationContinuous Illumination Set Targeting Zone TolerancesMedium Code Windowing Small Code Windowing WindowingLarge 2-Dimensional Codes 640 x 640 pixels Mirror Decoding VGA & Megapixel SettingsCodes Enable Sxga 1024 x Enable VGA 640 xAdding a Prefix or Suffix and Reader Text Commands Prefix Comma Prefix Space Prefix SettingsSuffix Settings Erase Prefix & Suffix Data Erase Prefix and Suffix SettingsReader Text Commands Reader Text Commands OnVS 2030 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory DefaultsWarranty Coverage and Procedure WarrantyLimited Warranty Terms of WarrantyGeneral VS 2030 Accessories TroubleshootingTechnical Support and Returns VS 2030 MaintenanceCleaning the VS 2030 Window Appendix a Reader Specifications Performance Characteristics Physical CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Control Setting Defaults Default SettingsSymbology Defaults Batch Mode Setting Defaults RS-232 Interface Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Handle Trigger Optimization and Settings Global All Trigger Optimization and SettingsLeft Trigger Optimization and Settings Right Trigger Optimization and SettingsSymbologies Continous Trigger Optimization and SettingsCode 39 On Default Reader Feedback Symbol Readability IndexKeypad Volume Backlight SettingsLaser Settings Illumination SettingsTargeting Zone Tolerances Reader Text CommandsReader Settings Locked Miscellaneous SettingsVS 2030 Programming Codes Batch Log Only Mode Batch Send & Log ModeBaud Rate Suffix Tab USB Keyboard Mode only RS232 Interface Baud RateSuffix Erase/None Default RS232 Interface Baud Rate RS232 InterfaceVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable Allow only Programming Data Matirx Codes Allow ALL Data Matrix Codes Default5 with Control Character Stripped Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off RSS Expanded On UPC Off UPC Extension Off QR Code On QR Code Off Default QR Code EnableQR Code Inverse On QR & Micro QR Code On Backlight Off Vibrate On Beep On Vibrate On Beep OffBacklight Intensity Low Backlight Intensity HighContinous Illumination Default Reader Power Off 1 HourKeypad Volume High Mirroring Off DefaultUS English ctrl + char Lockout Link Mode