Videk 2030 manual RS232 Cable Installation Guide, RS232 One Way Mode Save Settings, Baud Rate

Page 16

1.6.3 - RS232 Cable Installation Guide

To connect the VS 2030 to your host computer via RS232 interface:

1.Make sure the RS232 cable is sufficiently attached to your unit.

2.Connect the RS232 interface cable to your host computer. If you are unsure of the proper location to connect the RS232 cable please consult the manual of your host computer.

3.The RS232 interface is supplied with a power supply. Plug the power supply adapter into the RS232 interface cable and then plug the power adapter into a wall socket.

If you are using the RS232 interface and utilizing Batch functionality, please read the Important Note in batch section. If you are using the 1950 mAH battery for batch mode, the RS232 cable will recharge the VS 2030 battery only if the RS232 cable has a power supply connected and the power supply is plugged into a socket.

4.The VS 2030 will power on automatically.

5.Scan the RS232 One Way Mode code then the Save Settings code to configure reader:

RS232 One Way Mode	Save Settings	RS232 Factory Default Settings
		Mode: RS232 One Way Mode
		Baud Rate: 57600
		Stop Bits:	2
		Data Bits:	8
		Parity: None

6.Your VS 2030 unit should be ready for use. Open the application on your host computer that will receive scanned data and begin scanning.

Warning: Videk, Inc.-approved power adapter must be used. Reader failure due to use of incorrect power adapter will void all warranties.

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 10

Image 16

Contents Part Number K11020, Rev. E, August 3 Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents VS 2030 Programming Symbology Settings UPC/EAN/JANAppendix a Reader Specifications Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionRS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 ConsiderationsCabled Operation IntroductionUSB Cable Installation Guide USB Keyboard Default USB Downloader USB Virtual COM 1 Way ModeRS232 Cable Installation Guide RS232 One Way Mode Save SettingsMode RS232 One Way Mode Baud RateData Bits Data Bits Default Stop Bits Default1200 2400 4800 9600 19200 38400 Default 115200 Even Odd None DefaultCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultReader Feedback Guide RS232To read a symbol with the VS Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Read Codes with Both Imagers Default Left Trigger Optimization MatrixLeft Trigger Programming Read with Near-Field Imager onlyRight Trigger Programming Right Trigger Optimization MatrixRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger ProgrammingFar Field Only On Off Default Continuous Trigger Optimization MatrixContinuous Scan Both Near & Far Field OnMotion Detection Scan Settings Continuous Scan SettingsSeconds Default VS 2030 Programming Symbology Settings Aztec Symbology Codabar SymbologyCodablock F Symbology Code 11 SymbologyCode 39 Symbology Codablock F On Codablock F Off DefaultCode 93 Symbology Code 128 SymbologyCode 93 On Default Code 93 Off Sample Trioptic CodeData Matrix Symbology Composite SymbologiesComposite On Composite Off Default Interleaved 2 of 5 Symbology Maxicode SymbologyMSI Plessy Symbology Matrix 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 On NEC 2 of 5 Off Default NEC 2 of 5 SymbologyPharmacode Postal Symbologies Advanced Postal Symbologies UK ID Tag On Default UK ID Tag OffQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Volume and Vibration Settings Off Default Low MediumCode Readability Index Vibrate On / Beep On Vibrate On / Beep OffReadability Index Output Disable Backlight Intensity SettingsLow Med Default High Laser Settings Backlight Timeout SettingsReader Power Off Settings Reader Settings Lock Reader Settings LockedReader ID and Firmware Version Reader ID and FirmwareTime Stamp Settings US English Default US English LeadingKeyboard Support No Leading French GermanAdvanced Decode Performance Enable Continuous Illumination Continuous IlluminationSet Targeting Zone Tolerances 100 125Windowing Medium Code Windowing Small Code WindowingLarge 2-Dimensional Codes 640 x 640 pixels VGA & Megapixel Settings Codes Enable Sxga 1024 xEnable VGA 640 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Suffix Settings Prefix SettingsPrefix Comma Prefix Space Erase Prefix and Suffix Settings Reader Text CommandsReader Text Commands On Erase Prefix & Suffix DataVS 2030 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationWarranty Limited WarrantyTerms of Warranty Warranty Coverage and ProcedureVS 2030 Accessories Troubleshooting GeneralCleaning the VS 2030 Window VS 2030 MaintenanceTechnical Support and Returns Appendix a Reader Specifications Physical Characteristics Performance CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Symbology Defaults Default SettingsControl Setting Defaults RS-232 Interface Setting Defaults Batch Mode Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Global All Trigger Optimization and Settings Left Trigger Optimization and SettingsRight Trigger Optimization and Settings Handle Trigger Optimization and SettingsContinous Trigger Optimization and Settings SymbologiesCode 39 On Default Symbol Readability Index Reader FeedbackBacklight Settings Laser SettingsIllumination Settings Keypad VolumeReader Text Commands Reader Settings LockedMiscellaneous Settings Targeting Zone TolerancesBatch Log Only Mode Batch Send & Log Mode VS 2030 Programming CodesSuffix Tab USB Keyboard Mode only RS232 Interface Baud Rate Suffix Erase/None Default RS232 Interface Baud RateRS232 Interface Baud RateVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable 5 with Control Character Stripped Allow ALL Data Matrix Codes DefaultAllow only Programming Data Matirx Codes Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off QR Code Inverse On QR & Micro QR Code On QR Code On QR Code Off Default QR Code EnableRSS Expanded On UPC Off UPC Extension Off Vibrate On Beep On Vibrate On Beep Off Backlight Intensity LowBacklight Intensity High Backlight OffDefault Reader Power Off 1 Hour Keypad Volume HighMirroring Off Default Continous IlluminationUS English ctrl + char Lockout Link Mode