Videk 2030 VGA & Megapixel Settings, Mirror Decoding, Codes Enable Sxga 1024 x, Enable VGA 640 x

Page 54

5.4 - VGA & Megapixel Settings

User’s may optimize the VS 2030’s megapixel (SXGA) imager (1280 x 1024) to VGA (640 x 480). This feature is used to decrease the pixel sampling area, which will greatly increase processing speed. This is an advanced feature used for the rapid decoding of 1-dimensional/linear codes and larger module size 2- dimensional codes. Videk recommends testing this feature, as it will not work well with many high density

codes.	Enable SXGA - 1024 x 1280	Enable DOT (Default)
Enable VGA - 640 x 480

5.5 - Mirror Decoding

Scan the following codes to enable/disable the mirroring feature:

On	Off (Default)

Note: The Mirroring feature allows the VS 2030 to read codes as they are seen through a mirror (in- versed 180°). If the Mirroring feature is enabled, all other code reading ability will be disabled.

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 48

Image 54

Contents Part Number K11020, Rev. E, August 3 Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents VS 2030 Programming Symbology Settings UPC/EAN/JANAppendix a Reader Specifications Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionIntroduction RS232 Batch Cable-Detect DefaultBatch Operation RS232 ConsiderationsCabled Operation IntroductionUSB Cable Installation Guide USB Keyboard Default USB Downloader USB Virtual COM 1 Way ModeMode RS232 One Way Mode RS232 Cable Installation GuideRS232 One Way Mode Save Settings Baud Rate1200 2400 4800 9600 19200 38400 Default 115200 Data Bits Data Bits DefaultStop Bits Default Even Odd None DefaultCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultReader Feedback Guide RS232To read a symbol with the VS Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Left Trigger Programming Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Read with Near-Field Imager onlyRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger ProgrammingContinuous Scan Far Field Only On Off DefaultContinuous Trigger Optimization Matrix Both Near & Far Field OnContinuous Scan Settings Motion Detection Scan SettingsSeconds Default VS 2030 Programming Symbology Settings Aztec Symbology Codabar SymbologyCode 39 Symbology Codablock F SymbologyCode 11 Symbology Codablock F On Codablock F Off DefaultCode 93 On Default Code 93 Off Code 93 SymbologyCode 128 Symbology Sample Trioptic CodeComposite Symbologies Data Matrix SymbologyComposite On Composite Off Default Interleaved 2 of 5 Symbology Maxicode SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPharmacode Postal Symbologies Advanced Postal Symbologies UK ID Tag On Default UK ID Tag OffQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Code Readability Index Volume and Vibration SettingsOff Default Low Medium Vibrate On / Beep On Vibrate On / Beep OffBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader ID and Firmware Version Reader Settings LockReader Settings Locked Reader ID and FirmwareKeyboard Support Time Stamp SettingsUS English Default US English Leading No Leading French GermanAdvanced Decode Performance Set Targeting Zone Tolerances Enable Continuous IlluminationContinuous Illumination 100 125Windowing Medium Code Windowing Small Code WindowingLarge 2-Dimensional Codes 640 x 640 pixels Enable VGA 640 x VGA & Megapixel SettingsCodes Enable Sxga 1024 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Prefix Settings Suffix SettingsPrefix Comma Prefix Space Reader Text Commands On Erase Prefix and Suffix SettingsReader Text Commands Erase Prefix & Suffix DataVS 2030 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationTerms of Warranty WarrantyLimited Warranty Warranty Coverage and ProcedureVS 2030 Accessories Troubleshooting GeneralVS 2030 Maintenance Cleaning the VS 2030 WindowTechnical Support and Returns Appendix a Reader Specifications Physical Characteristics Performance CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Default Settings Symbology DefaultsControl Setting Defaults RS-232 Interface Setting Defaults Batch Mode Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Right Trigger Optimization and Settings Global All Trigger Optimization and SettingsLeft Trigger Optimization and Settings Handle Trigger Optimization and SettingsContinous Trigger Optimization and Settings SymbologiesCode 39 On Default Symbol Readability Index Reader FeedbackIllumination Settings Backlight SettingsLaser Settings Keypad VolumeMiscellaneous Settings Reader Text CommandsReader Settings Locked Targeting Zone TolerancesBatch Log Only Mode Batch Send & Log Mode VS 2030 Programming CodesRS232 Interface Suffix Tab USB Keyboard Mode only RS232 Interface Baud RateSuffix Erase/None Default RS232 Interface Baud Rate Baud RateVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable Allow ALL Data Matrix Codes Default 5 with Control Character StrippedAllow only Programming Data Matirx Codes Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off QR Code On QR Code Off Default QR Code Enable QR Code Inverse On QR & Micro QR Code OnRSS Expanded On UPC Off UPC Extension Off Backlight Intensity High Vibrate On Beep On Vibrate On Beep OffBacklight Intensity Low Backlight OffMirroring Off Default Default Reader Power Off 1 HourKeypad Volume High Continous IlluminationUS English ctrl + char Lockout Link Mode