Videk 2030 manual Telepen Symbology, Upc/Ean/Jan

Page 43

Sample RSS Limited Code

Sample RSS 14 Code

Sample RSS 14 Truncated Code

Sample RSS 14 Stacked Code

3.23 - Telepen Symbology

Scan the following codes to enable/disable Telepen symbology settings:

Telepen On - Default

Telepen Off

Sample Telepen

3.24 - UPC/EAN/JAN

Scan the following codes to enable/disable UPC/EAN/JAN symbology settings:

UPC On (Default)

UPC Off

UPC Short Margin Enabled

UPC Short Margin Disabled (Default)

UPC Extension On

UPC Extension Off

Sample UPC A Code

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 37

Image 43

Contents Part Number K11020, Rev. E, August 3 Laser/LED Radiation Statement of Agency ComplianceSave Settings Table of Contents UPC/EAN/JAN VS 2030 Programming Symbology Settings Appendix a Reader Specifications Getting Started Introduction Unpacking Powering On/Off ReaderDescription of Button Function Keypad/Icon OverviewIcon Description Power IconsRS232 Considerations RS232 Batch Cable-Detect DefaultBatch Operation IntroductionIntroduction Cabled OperationUSB Cable Installation Guide USB Virtual COM 1 Way Mode USB Keyboard Default USB DownloaderBaud Rate RS232 Cable Installation GuideRS232 One Way Mode Save Settings Mode RS232 One Way ModeEven Odd None Default Data Bits Data Bits DefaultStop Bits Default 1200 2400 4800 9600 19200 38400 Default 115200Cabled 2 hours Cabled Always Default Cabled Reader Time Out SettingsRS232 Reader Feedback GuideTargeting and Reading Techniques To read a symbol with the VSImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming DOT IntroductionGlobal Trigger Optimization Matrix Read with Near-Field Imager only Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Left Trigger ProgrammingRight Trigger Programming Right Trigger Optimization MatrixRead Code with Near-Field Imager only Handle Trigger Programming Handle Optimization MatrixBoth Near & Far Field On Far Field Only On Off DefaultContinuous Trigger Optimization Matrix Continuous ScanMotion Detection Scan Settings Continuous Scan SettingsSeconds Default VS 2030 Programming Symbology Settings Codabar Symbology Aztec SymbologyCodablock F On Codablock F Off Default Codablock F SymbologyCode 11 Symbology Code 39 SymbologySample Trioptic Code Code 93 SymbologyCode 128 Symbology Code 93 On Default Code 93 OffData Matrix Symbology Composite SymbologiesComposite On Composite Off Default Maxicode Symbology Interleaved 2 of 5 SymbologyMSI Plessy Symbology Matrix 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 On NEC 2 of 5 Off Default NEC 2 of 5 SymbologyPharmacode Postal Symbologies UK ID Tag On Default UK ID Tag Off Advanced Postal SymbologiesRSS Symbology QR Code SymbologyUPC/EAN/JAN Telepen SymbologyReader Feedback and Special Settings Vibrate On / Beep On Vibrate On / Beep Off Volume and Vibration SettingsOff Default Low Medium Code Readability IndexReadability Index Output Disable Backlight Intensity SettingsLow Med Default High Laser Settings Backlight Timeout SettingsReader Power Off Settings Reader ID and Firmware Reader Settings LockReader Settings Locked Reader ID and Firmware VersionNo Leading French German Time Stamp SettingsUS English Default US English Leading Keyboard SupportAdvanced Decode Performance 100 125 Enable Continuous IlluminationContinuous Illumination Set Targeting Zone TolerancesMedium Code Windowing Small Code Windowing WindowingLarge 2-Dimensional Codes 640 x 640 pixels Mirror Decoding VGA & Megapixel SettingsCodes Enable Sxga 1024 x Enable VGA 640 xAdding a Prefix or Suffix and Reader Text Commands Suffix Settings Prefix SettingsPrefix Comma Prefix Space Erase Prefix & Suffix Data Erase Prefix and Suffix SettingsReader Text Commands Reader Text Commands OnVS 2030 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory DefaultsWarranty Coverage and Procedure WarrantyLimited Warranty Terms of WarrantyGeneral VS 2030 Accessories TroubleshootingCleaning the VS 2030 Window VS 2030 MaintenanceTechnical Support and Returns Appendix a Reader Specifications Performance Characteristics Physical CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Symbology Defaults Default SettingsControl Setting Defaults Batch Mode Setting Defaults RS-232 Interface Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Handle Trigger Optimization and Settings Global All Trigger Optimization and SettingsLeft Trigger Optimization and Settings Right Trigger Optimization and SettingsSymbologies Continous Trigger Optimization and SettingsCode 39 On Default Reader Feedback Symbol Readability IndexKeypad Volume Backlight SettingsLaser Settings Illumination SettingsTargeting Zone Tolerances Reader Text CommandsReader Settings Locked Miscellaneous SettingsVS 2030 Programming Codes Batch Log Only Mode Batch Send & Log ModeBaud Rate Suffix Tab USB Keyboard Mode only RS232 Interface Baud RateSuffix Erase/None Default RS232 Interface Baud Rate RS232 InterfaceVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable 5 with Control Character Stripped Allow ALL Data Matrix Codes DefaultAllow only Programming Data Matirx Codes Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off QR Code Inverse On QR & Micro QR Code On QR Code On QR Code Off Default QR Code EnableRSS Expanded On UPC Off UPC Extension Off Backlight Off Vibrate On Beep On Vibrate On Beep OffBacklight Intensity Low Backlight Intensity HighContinous Illumination Default Reader Power Off 1 HourKeypad Volume High Mirroring Off DefaultUS English ctrl + char Lockout Link Mode