Videk 2030 manual Default Settings, Symbology Defaults, Control Setting Defaults

Page 75

Default Settings

The following are the primary default settings for your VisionSensor 2030. Refer to the manual text for secondary default settings that relate to specific code types or other reader attributes.

Symbology Defaults:
Aztec		OFF
Codabar		ON
Codablock F		OFF
Code 11		ON
Code 39		ON
Code 93		ON
Code 128		ON
Composite		OFF
Data Matrix		ON
Interleaved 2 of 5		ON
Matrix 2 of 5		OFF
MaxiCode		OFF
MacroPDF417		OFF
MicroPDF417		OFF
MSI Plessy		OFF
NEC 2 of 5		OFF
PDF417		ON
Pharmacode		OFF
Postal Codes (ONLY the following: Posnet, Planet, 4-CB, ID Tag/S18D, UK ID Tag)		.............................. ON
QR Code		OFF
RSS		OFF
Telepen		ON
UPC/EAN/JAN		ON
Control Setting Defaults:
Communication Mode		USB Keyboard
Left Button		All Decodes
Right Button		All Decodes
Handle	Both Near and Far
Beeper Volume		High
Vibrate Off / Beep On		Enabled
Keypad Button Press Sounds		Off
Backlight Intensity		Medium
Backlight Timeout		3 Seconds
Reader Power Off (Sleep)		2 Hours
Time Stamp		OFF
Continuous Scan		OFF
Code Readability Index Output		Enabled

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 69
Save Settings

Image 75

Contents Part Number K11020, Rev. E, August 3 Laser/LED Radiation Statement of Agency ComplianceSave Settings Table of Contents UPC/EAN/JAN VS 2030 Programming Symbology Settings Appendix a Reader Specifications Getting Started Introduction Unpacking Powering On/Off ReaderDescription of Button Function Keypad/Icon OverviewIcon Description Power IconsRS232 Considerations RS232 Batch Cable-Detect DefaultBatch Operation IntroductionIntroduction Cabled OperationUSB Cable Installation Guide USB Virtual COM 1 Way Mode USB Keyboard Default USB DownloaderBaud Rate RS232 Cable Installation GuideRS232 One Way Mode Save Settings Mode RS232 One Way ModeEven Odd None Default Data Bits Data Bits DefaultStop Bits Default 1200 2400 4800 9600 19200 38400 Default 115200Cabled 2 hours Cabled Always Default Cabled Reader Time Out SettingsRS232 Reader Feedback GuideTargeting and Reading Techniques To read a symbol with the VSImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming DOT IntroductionGlobal Trigger Optimization Matrix Read with Near-Field Imager only Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Left Trigger ProgrammingRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Trigger Programming Handle Optimization MatrixBoth Near & Far Field On Far Field Only On Off DefaultContinuous Trigger Optimization Matrix Continuous ScanContinuous Scan Settings Motion Detection Scan SettingsSeconds Default VS 2030 Programming Symbology Settings Codabar Symbology Aztec SymbologyCodablock F On Codablock F Off Default Codablock F SymbologyCode 11 Symbology Code 39 SymbologySample Trioptic Code Code 93 SymbologyCode 128 Symbology Code 93 On Default Code 93 OffComposite Symbologies Data Matrix SymbologyComposite On Composite Off Default Maxicode Symbology Interleaved 2 of 5 SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPharmacode Postal Symbologies UK ID Tag On Default UK ID Tag Off Advanced Postal SymbologiesRSS Symbology QR Code SymbologyUPC/EAN/JAN Telepen SymbologyReader Feedback and Special Settings Vibrate On / Beep On Vibrate On / Beep Off Volume and Vibration SettingsOff Default Low Medium Code Readability IndexBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader ID and Firmware Reader Settings LockReader Settings Locked Reader ID and Firmware VersionNo Leading French German Time Stamp SettingsUS English Default US English Leading Keyboard SupportAdvanced Decode Performance 100 125 Enable Continuous IlluminationContinuous Illumination Set Targeting Zone TolerancesMedium Code Windowing Small Code Windowing WindowingLarge 2-Dimensional Codes 640 x 640 pixels Mirror Decoding VGA & Megapixel SettingsCodes Enable Sxga 1024 x Enable VGA 640 xAdding a Prefix or Suffix and Reader Text Commands Prefix Settings Suffix SettingsPrefix Comma Prefix Space Erase Prefix & Suffix Data Erase Prefix and Suffix SettingsReader Text Commands Reader Text Commands OnVS 2030 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory DefaultsWarranty Coverage and Procedure WarrantyLimited Warranty Terms of WarrantyGeneral VS 2030 Accessories TroubleshootingVS 2030 Maintenance Cleaning the VS 2030 WindowTechnical Support and Returns Appendix a Reader Specifications Performance Characteristics Physical CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Default Settings Symbology DefaultsControl Setting Defaults Batch Mode Setting Defaults RS-232 Interface Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Handle Trigger Optimization and Settings Global All Trigger Optimization and SettingsLeft Trigger Optimization and Settings Right Trigger Optimization and SettingsSymbologies Continous Trigger Optimization and SettingsCode 39 On Default Reader Feedback Symbol Readability IndexKeypad Volume Backlight SettingsLaser Settings Illumination SettingsTargeting Zone Tolerances Reader Text CommandsReader Settings Locked Miscellaneous SettingsVS 2030 Programming Codes Batch Log Only Mode Batch Send & Log ModeBaud Rate Suffix Tab USB Keyboard Mode only RS232 Interface Baud RateSuffix Erase/None Default RS232 Interface Baud Rate RS232 InterfaceVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable Allow ALL Data Matrix Codes Default 5 with Control Character StrippedAllow only Programming Data Matirx Codes Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off QR Code On QR Code Off Default QR Code Enable QR Code Inverse On QR & Micro QR Code OnRSS Expanded On UPC Off UPC Extension Off Backlight Off Vibrate On Beep On Vibrate On Beep OffBacklight Intensity Low Backlight Intensity HighContinous Illumination Default Reader Power Off 1 HourKeypad Volume High Mirroring Off DefaultUS English ctrl + char Lockout Link Mode