Videk 2030 manual Aztec Symbology, Codabar Symbology

Page 33

3.1 - Introduction

The following chapter will allow a user to change the symbology settings on the VS 2030. To reset the unit to factory defaults or to save the current settings please scan one of the codes below:

Save Settings

Reset to USB Factory Defaults

Reset to RS232	Clear All CodeXML Rules
Factory Defaults

Readers are shipped from manufacturing with initial communication settings that are hardware dependent. Note: If you do not save your settings and the VS 2030 loses power you will lose your settings.

3.2 - Aztec Symbology

Scan the following codes to enable/disable Aztec symbology settings:

Aztec On

Aztec Off (Default)

Sample Aztec Code

3.3 - Codabar Symbology

Scan the following codes to enable/disable Codabar symbology settings:

Codabar On (Default)

Codabar Off

Sample Codabar

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 27

Image 33

Contents Part Number K11020, Rev. E, August 3 Laser/LED Radiation Statement of Agency ComplianceSave Settings Table of Contents UPC/EAN/JAN VS 2030 Programming Symbology Settings Appendix a Reader Specifications Getting Started Introduction Unpacking Powering On/Off ReaderDescription of Button Function Keypad/Icon OverviewIcon Description Power IconsBatch Operation RS232 Batch Cable-Detect DefaultIntroduction RS232 ConsiderationsIntroduction Cabled OperationUSB Cable Installation Guide USB Virtual COM 1 Way Mode USB Keyboard Default USB DownloaderRS232 One Way Mode Save Settings RS232 Cable Installation GuideMode RS232 One Way Mode Baud RateStop Bits Default Data Bits Data Bits Default1200 2400 4800 9600 19200 38400 Default 115200 Even Odd None DefaultCabled 2 hours Cabled Always Default Cabled Reader Time Out SettingsRS232 Reader Feedback GuideTargeting and Reading Techniques To read a symbol with the VSImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming DOT IntroductionGlobal Trigger Optimization Matrix Left Trigger Optimization Matrix Read Codes with Both Imagers DefaultLeft Trigger Programming Read with Near-Field Imager onlyRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Trigger Programming Handle Optimization MatrixContinuous Trigger Optimization Matrix Far Field Only On Off DefaultContinuous Scan Both Near & Far Field OnContinuous Scan Settings Motion Detection Scan SettingsSeconds Default VS 2030 Programming Symbology Settings Codabar Symbology Aztec SymbologyCode 11 Symbology Codablock F SymbologyCode 39 Symbology Codablock F On Codablock F Off DefaultCode 128 Symbology Code 93 SymbologyCode 93 On Default Code 93 Off Sample Trioptic CodeComposite Symbologies Data Matrix SymbologyComposite On Composite Off Default Maxicode Symbology Interleaved 2 of 5 SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPharmacode Postal Symbologies UK ID Tag On Default UK ID Tag Off Advanced Postal SymbologiesRSS Symbology QR Code SymbologyUPC/EAN/JAN Telepen SymbologyReader Feedback and Special Settings Off Default Low Medium Volume and Vibration SettingsCode Readability Index Vibrate On / Beep On Vibrate On / Beep OffBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader Settings Locked Reader Settings LockReader ID and Firmware Version Reader ID and FirmwareUS English Default US English Leading Time Stamp SettingsKeyboard Support No Leading French GermanAdvanced Decode Performance Continuous Illumination Enable Continuous IlluminationSet Targeting Zone Tolerances 100 125Medium Code Windowing Small Code Windowing WindowingLarge 2-Dimensional Codes 640 x 640 pixels Codes Enable Sxga 1024 x VGA & Megapixel SettingsEnable VGA 640 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Prefix Settings Suffix SettingsPrefix Comma Prefix Space Reader Text Commands Erase Prefix and Suffix SettingsReader Text Commands On Erase Prefix & Suffix DataVS 2030 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory DefaultsLimited Warranty WarrantyTerms of Warranty Warranty Coverage and ProcedureGeneral VS 2030 Accessories TroubleshootingVS 2030 Maintenance Cleaning the VS 2030 WindowTechnical Support and Returns Appendix a Reader Specifications Performance Characteristics Physical CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Default Settings Symbology DefaultsControl Setting Defaults Batch Mode Setting Defaults RS-232 Interface Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Left Trigger Optimization and Settings Global All Trigger Optimization and SettingsRight Trigger Optimization and Settings Handle Trigger Optimization and SettingsSymbologies Continous Trigger Optimization and SettingsCode 39 On Default Reader Feedback Symbol Readability IndexLaser Settings Backlight SettingsIllumination Settings Keypad VolumeReader Settings Locked Reader Text CommandsMiscellaneous Settings Targeting Zone TolerancesVS 2030 Programming Codes Batch Log Only Mode Batch Send & Log ModeSuffix Erase/None Default RS232 Interface Baud Rate Suffix Tab USB Keyboard Mode only RS232 Interface Baud RateRS232 Interface Baud RateVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable Allow ALL Data Matrix Codes Default 5 with Control Character StrippedAllow only Programming Data Matirx Codes Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off QR Code On QR Code Off Default QR Code Enable QR Code Inverse On QR & Micro QR Code OnRSS Expanded On UPC Off UPC Extension Off Backlight Intensity Low Vibrate On Beep On Vibrate On Beep OffBacklight Intensity High Backlight OffKeypad Volume High Default Reader Power Off 1 HourMirroring Off Default Continous IlluminationUS English ctrl + char Lockout Link Mode