Videk 2030 manual USB Cable Installation Guide

Page 14

1.6.2 - USB Cable Installation Guide

To connect the VS 2030 to your host computer via USB interface:

1.Make sure the USB cable is sufficiently attached to your VS

2030 unit.

2.You DO NOT need to power off your host computer. The VS

2030 with USB interface can be plugged into any host while the computer is powered up.

3.Connect the USB interface cable to the host. If you are unsure of the proper location to connect the USB cable please consult the manual of your host computer.

4.The USB interface does not require additional power supply.

The VS 2030 will automatically recharge the battery whenever the unit is attached to a host that is powered up.

5.The VS 2030 will power on automatically.

6.Your VS 2030 unit should be ready for use. Open the applica- tion on your host computer to which you wish to send data and begin scanning.

	Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 -
	Save Settings

Image 14

Contents Part Number K11020, Rev. E, August 3 Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents VS 2030 Programming Symbology Settings UPC/EAN/JANAppendix a Reader Specifications Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionIntroduction RS232 Batch Cable-Detect DefaultBatch Operation RS232 ConsiderationsCabled Operation IntroductionUSB Cable Installation Guide USB Keyboard Default USB Downloader USB Virtual COM 1 Way ModeMode RS232 One Way Mode RS232 Cable Installation GuideRS232 One Way Mode Save Settings Baud Rate1200 2400 4800 9600 19200 38400 Default 115200 Data Bits Data Bits DefaultStop Bits Default Even Odd None DefaultCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultReader Feedback Guide RS232To read a symbol with the VS Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Left Trigger Programming Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Read with Near-Field Imager onlyRead Code with Near-Field Imager only Right Trigger Optimization MatrixRight Trigger Programming Handle Optimization Matrix Handle Trigger ProgrammingContinuous Scan Far Field Only On Off DefaultContinuous Trigger Optimization Matrix Both Near & Far Field OnSeconds Default Continuous Scan SettingsMotion Detection Scan Settings VS 2030 Programming Symbology Settings Aztec Symbology Codabar SymbologyCode 39 Symbology Codablock F SymbologyCode 11 Symbology Codablock F On Codablock F Off DefaultCode 93 On Default Code 93 Off Code 93 SymbologyCode 128 Symbology Sample Trioptic CodeComposite On Composite Off Default Composite SymbologiesData Matrix Symbology Interleaved 2 of 5 Symbology Maxicode SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy Matrix 2 of 5 SymbologyMSI Plessy Symbology Pharmacode NEC 2 of 5 SymbologyNEC 2 of 5 On NEC 2 of 5 Off Default Postal Symbologies Advanced Postal Symbologies UK ID Tag On Default UK ID Tag OffQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Code Readability Index Volume and Vibration SettingsOff Default Low Medium Vibrate On / Beep On Vibrate On / Beep OffLow Med Default High Backlight Intensity SettingsReadability Index Output Disable Reader Power Off Settings Backlight Timeout SettingsLaser Settings Reader ID and Firmware Version Reader Settings LockReader Settings Locked Reader ID and FirmwareKeyboard Support Time Stamp SettingsUS English Default US English Leading No Leading French GermanAdvanced Decode Performance Set Targeting Zone Tolerances Enable Continuous IlluminationContinuous Illumination 100 125Windowing Medium Code Windowing Small Code WindowingLarge 2-Dimensional Codes 640 x 640 pixels Enable VGA 640 x VGA & Megapixel SettingsCodes Enable Sxga 1024 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Prefix Comma Prefix Space Prefix SettingsSuffix Settings Reader Text Commands On Erase Prefix and Suffix SettingsReader Text Commands Erase Prefix & Suffix DataVS 2030 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationTerms of Warranty WarrantyLimited Warranty Warranty Coverage and ProcedureVS 2030 Accessories Troubleshooting GeneralTechnical Support and Returns VS 2030 MaintenanceCleaning the VS 2030 Window Appendix a Reader Specifications Physical Characteristics Performance CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Control Setting Defaults Default SettingsSymbology Defaults RS-232 Interface Setting Defaults Batch Mode Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Right Trigger Optimization and Settings Global All Trigger Optimization and SettingsLeft Trigger Optimization and Settings Handle Trigger Optimization and SettingsContinous Trigger Optimization and Settings SymbologiesCode 39 On Default Symbol Readability Index Reader FeedbackIllumination Settings Backlight SettingsLaser Settings Keypad VolumeMiscellaneous Settings Reader Text CommandsReader Settings Locked Targeting Zone TolerancesBatch Log Only Mode Batch Send & Log Mode VS 2030 Programming CodesRS232 Interface Suffix Tab USB Keyboard Mode only RS232 Interface Baud RateSuffix Erase/None Default RS232 Interface Baud Rate Baud RateVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable Allow only Programming Data Matirx Codes Allow ALL Data Matrix Codes Default5 with Control Character Stripped Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off RSS Expanded On UPC Off UPC Extension Off QR Code On QR Code Off Default QR Code EnableQR Code Inverse On QR & Micro QR Code On Backlight Intensity High Vibrate On Beep On Vibrate On Beep OffBacklight Intensity Low Backlight OffMirroring Off Default Default Reader Power Off 1 HourKeypad Volume High Continous IlluminationUS English ctrl + char Lockout Link Mode