Videk 2030 manual Targeting and Reading Techniques, To read a symbol with the VS

Page 20

1.8 - Targeting and Reading Techniques

The VS 2030 utilizes digital camera technology to take a picture of a symbol. Once an image is captured, the VS 2030 utilizes advanced decoding algorithms to extract data from the captured image.

The VS 2030 features left and right triggers (the red buttons on the top of the reader). These triggers may be programmed to perform various features. The reader is shipped with the left trigger and right trigger functioning as a decode symbol command.

The handle has a trigger on the grip. The two triggers on the top of the unit also work when the handle is attached.

To read a symbol with the VS 2030:

1.The VS 2030 features omnidirectional decoding. Center the symbol in any orientation within the laser dot aiming pattern.

Note: The VS 2030 can read a symbol that is not centered; however, the VS 2030 performs best when a code is centered. If two (2) bar codes are with the imagers decode zone, the VS 2030 will decode the symbol closest to the center of the aiming dot.

2.The VS 2030 was developed to decode both very small 2-dimensional symbols and larger 1-dimen- sional symbols. The unit has an innovative dual field decode zone. The VS 2030 DECODES BOTH ZONES SIMULTANEOUSLY. The unit has a lens focused on a near-field for smaller codes (optimal focal point is 4 inches) and one lens focused on a far-field for larger codes (optimal focal point 9 inches). To read smaller symbols move the VS 2030 closer to the symbol. To read larger symbols move the unit farther away from the symbol. The entire VS 2030 decode zone varies between two

(2”) and twenty (20+”) or more inches. For postal codes the range is between eight (8”) and ten (10”) inches.

3.Hold the VS 2030 steady - DO NOT SWIPE OR MOVE THE READER. Press the trigger until the VS 2030 beeps, indicating the code has been successfully decoded.

4.The reader may be optimized to your specific environment by scanning codes in Chapter 2.

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 14

Image 20

Contents Part Number K11020, Rev. E, August 3 Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents VS 2030 Programming Symbology Settings UPC/EAN/JANAppendix a Reader Specifications Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionRS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 ConsiderationsCabled Operation IntroductionUSB Cable Installation Guide USB Keyboard Default USB Downloader USB Virtual COM 1 Way ModeRS232 Cable Installation Guide RS232 One Way Mode Save SettingsMode RS232 One Way Mode Baud RateData Bits Data Bits Default Stop Bits Default1200 2400 4800 9600 19200 38400 Default 115200 Even Odd None DefaultCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultReader Feedback Guide RS232To read a symbol with the VS Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Read Codes with Both Imagers Default Left Trigger Optimization MatrixLeft Trigger Programming Read with Near-Field Imager onlyRead Code with Near-Field Imager only Right Trigger Optimization MatrixRight Trigger Programming Handle Optimization Matrix Handle Trigger ProgrammingFar Field Only On Off Default Continuous Trigger Optimization MatrixContinuous Scan Both Near & Far Field OnSeconds Default Continuous Scan SettingsMotion Detection Scan Settings VS 2030 Programming Symbology Settings Aztec Symbology Codabar SymbologyCodablock F Symbology Code 11 SymbologyCode 39 Symbology Codablock F On Codablock F Off DefaultCode 93 Symbology Code 128 SymbologyCode 93 On Default Code 93 Off Sample Trioptic CodeComposite On Composite Off Default Composite SymbologiesData Matrix Symbology Interleaved 2 of 5 Symbology Maxicode SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy Matrix 2 of 5 SymbologyMSI Plessy Symbology Pharmacode NEC 2 of 5 SymbologyNEC 2 of 5 On NEC 2 of 5 Off Default Postal Symbologies Advanced Postal Symbologies UK ID Tag On Default UK ID Tag OffQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Volume and Vibration Settings Off Default Low MediumCode Readability Index Vibrate On / Beep On Vibrate On / Beep OffLow Med Default High Backlight Intensity SettingsReadability Index Output Disable Reader Power Off Settings Backlight Timeout SettingsLaser Settings Reader Settings Lock Reader Settings LockedReader ID and Firmware Version Reader ID and FirmwareTime Stamp Settings US English Default US English LeadingKeyboard Support No Leading French GermanAdvanced Decode Performance Enable Continuous Illumination Continuous IlluminationSet Targeting Zone Tolerances 100 125Windowing Medium Code Windowing Small Code WindowingLarge 2-Dimensional Codes 640 x 640 pixels VGA & Megapixel Settings Codes Enable Sxga 1024 xEnable VGA 640 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Prefix Comma Prefix Space Prefix SettingsSuffix Settings Erase Prefix and Suffix Settings Reader Text CommandsReader Text Commands On Erase Prefix & Suffix DataVS 2030 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationWarranty Limited WarrantyTerms of Warranty Warranty Coverage and ProcedureVS 2030 Accessories Troubleshooting GeneralTechnical Support and Returns VS 2030 MaintenanceCleaning the VS 2030 Window Appendix a Reader Specifications Physical Characteristics Performance CharacteristicsUser Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Control Setting Defaults Default SettingsSymbology Defaults RS-232 Interface Setting Defaults Batch Mode Setting DefaultsAppendix E Programming Codes Appendix E Table of Contents Global All Trigger Optimization and Settings Left Trigger Optimization and SettingsRight Trigger Optimization and Settings Handle Trigger Optimization and SettingsContinous Trigger Optimization and Settings SymbologiesCode 39 On Default Symbol Readability Index Reader FeedbackBacklight Settings Laser SettingsIllumination Settings Keypad VolumeReader Text Commands Reader Settings LockedMiscellaneous Settings Targeting Zone TolerancesBatch Log Only Mode Batch Send & Log Mode VS 2030 Programming CodesSuffix Tab USB Keyboard Mode only RS232 Interface Baud Rate Suffix Erase/None Default RS232 Interface Baud RateRS232 Interface Baud RateVS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable Allow only Programming Data Matirx Codes Allow ALL Data Matrix Codes Default5 with Control Character Stripped Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off RSS Expanded On UPC Off UPC Extension Off QR Code On QR Code Off Default QR Code EnableQR Code Inverse On QR & Micro QR Code On Vibrate On Beep On Vibrate On Beep Off Backlight Intensity LowBacklight Intensity High Backlight OffDefault Reader Power Off 1 Hour Keypad Volume HighMirroring Off Default Continous IlluminationUS English ctrl + char Lockout Link Mode