Air Vent Inc IM10065 manual Company

Page 17

A-7	INSTALLATION	A-7

2.Take necessary steps to assure load is limited to the capacity of the AIR VANTAGE® 500 CUMMINS by installing a 50 amp, 240 VAC double pole circuit breaker. Maximum rated load for each leg of the 240 VAC auxiliary is 50 amps. Loading above the rated output will reduce output voltage below the allowable -10% of rated voltage which may damage appliances or other motor-driven equipment and may result in overheating of the AIR VANTAGE® 500 CUMMINS engine.

3.Install a 50 amp 120/240 VAC plug (NEMA Type 14-50) to the double-pole circuit breaker using No. 6, 4 conductor cable of the desired length. (The 50 amp, 120/240 VAC plug is available in the optional K802R plug kit.)

4.Plug this cable into the 50 Amp 120/240 Volt recep- tacle on the AIR VANTAGE® 500 CUMMINS case front.

Figure A.1 Connection of the AIR VANTAGE® 500 to Premises Wiring

			240 VOLT
	240	Volt	POWER
			120 VOLT
	60 Hz.
			COMPANY
	3-Wire
			120 VOLT
	Service
			METER

GROUNDED CONDUCTOR

NEUTRAL

BUS

N

LOAD

DOUBLE POLE DOUBLE THROW

SWITCH RATING TO BE THE SAME

AS OR GREATER THAN PREMISES

SERVICE OVERCURRENT

PROTECTION.

50 AMP, 120/240

VOLT PLUG240 VOLT NEMA TYPE 14-50

50AMP

240 VOLT

DOUBLE

POLE

CIRCUIT

BREAKER

GND

N

PREMISES

DISCONNECT AND

SERVICE

GROUNDOVERCURRENT PROTECTION

50 AMP, 120/240 VOLT

RECEPTACLENOTE: No. 6 COPPER CONDUCTOR CABLE SEE NATIONAL ELECTRICAL CODE FOR ALTERNATE WIRE

SIZE RECOMMENDATIONS.

AIR VANTAGE® 500 CUMMINS

Image 17

Contents 11651 Safety Depends on YouCalifornia Proposition 65 Warnings SafetyIiSAFETY Iii IiiSAFETYPrécautions DE Sûreté IvSAFETYElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply On-Line Product Registration ViiPlease Examine Carton and Equipment For Damage Immediately TAbLE of Contents TAbLE of Contents Technical Specifications AIR Vantage 500 Cummins K2325-3 InstallationLocation and Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation Towing OIL PRE-OPERATION Engine and COM- Pressor Service Fuel USE Diesel Fuel only Fuel CAPMuffler Outlet Pipe AIR Cleaner Inlet HoodSpark Arrestor Welding TerminalsSTANDbY Power Connections Remote ControlAuxiliary Power Receptacles Company Connection of LN-15 to the AIR Vantage 500 Cummins Connection of Lincoln ELEC- Tric Wire FeedersAcross The-Arc Model Control Cable ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the AIR Vantage 500 CumminsGeneral Description OperationRUN Stop Switch Controls and SettingsEngine Temperature Gauge Hour MeterIdler Switch BATTERY Charging LightOIL Pressure Gauge ENGINE PROTECTIONWelding Terminals Switch WELD MODE SELECTOR SWITCHWIRE FEEDER VOLTMETER SWITCH PIN ConnectorAIR Compressor Controls 24 Thru Starting the Engine Engine OperationCold Weather Starting Stopping the EngineWelder Operation Table b.3 Typical Current Ranges Wire WELDING-CVARC Gouging Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationBOTH 1 and 3 Phase ParallelingOptional Field Installed Accessories AccessoriesTIG Options K2641-2 Four Wheeled STEERAbLE Yard TrailerCompressor Maintenance MaintenanceSingle- and Two-StageEngine Air Cleaners Service InstructionsPreventing Electrical Damage Fuel FiltersCooling System Gfci Receptacle Testing and RESET- Ting Procedure CleaningWelder / Generator MAINTE- Nance Nameplates / Warning Decals MAIN- TenanceTROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionTROUbLESHOOTING Maintenance section of Authorized Field Service Facility Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Dimension Print AIR Vantage 500 Cummins Precaucion Warnung