Air Vent Inc IM10065 manual Lifting, High Altitude Operation, High Temperature Operation, Towing

Page 13

A-3

INSTALLATION

A-3

 

 

 

LIFTING

The AIR VANTAGE® 500 CUMMINS lift bale should be used to lift the machine. The Air Vantage 500 is shipped with the lift bale retracted. Before attempting to lift the AIR VANTAGE® 500 CUMMINS the lift bale must be secured in a raised position. Secure the lift bale as follows:

a. Open the engine compartment door.

b. Locate the 2 access holes on the upper middle region of compartment wall just below the lift bale.

c. Use the lifting strap to raise the lift bale to the full upright position. This will align the mount- ing holes on the lift bale with the access holes.

d. Secure the lift bale with 2 thread forming screws. The screws are provided in the shipped loose parts bag.

WARNING

•Lift only with equipment of ade- quate lifting capacity.

•be sure machine is stable when lift- ing.

•Do not lift this machine using lift bail if it is equipped with a heavy

 

accessory such as trailer or gas

 

cylinder.

FALLING

• Do not lift machine if lift bail is

EQUIPMENT can

damaged.

cause injury.

• Do not operate machine while

 

suspended from lift bail.

------------------------------------------------------------------------

HIGH ALTITUDE OPERATION

At higher altitudes, output derating may be necessary. For maximum rating, derate the welder output 4% for every 300 meters (984 ft.) above 1500 meters (4920 ft.). For output of 500A and below, derate the welder output 4% for every 300 meters (984 ft.) above 2100 meters (6888 ft.).

Contact a Cummins Service Representative for any engine adjustments that may be required.

HIGH TEMPERATURE OPERATION

At temperatures above 40°C (104°F), output voltage derating may be necessary. For maximum output cur- rent ratings, derate welder voltage rating 2 volts for every 10°C (21°F) above 40°C (104°F).

TOWING

The recommended trailer for use with this equipment for road, in-plant and yard towing by a vehicle (1) is Lincoln’s K2636-1. If the user adapts a non-Lincoln trailer, he must assume responsibility that the method of attachment and usage does not result in a safety hazard nor damage the welding equipment. Some of the factors to be considered are as follows:

1.Design capacity of trailer vs. weight of Lincoln equipment and likely additional attachments.

2.Proper support of, and attachment to, the base of the welding equipment so that there will be no undue stress to the trailer’s framework.

3.Proper placement of the equipment on the trailer to insure stability side to side and front to back when being moved and when standing by itself.

4.Typical conditions of use, such as travel speed, roughness of surface on which the trailer will be operated, and environmental conditions.

5.Proper preventative maintenance of trailer.

6.Conformance with federal, state and local laws(1).

(1)Consult applicable federal, state and local laws regarding specific requirements for use on public highways.

VEHICLE MOUNTING

WARNING

Improperly mounted concentrated loads may cause unstable vehicle handling and tires or other components to fail.

•Only transport this Equipment on serviceable vehicles which are rated and designed for such loads.

•Distribute, balance and secure loads so vehicle is stable under conditions of use.

•Do not exceed maximum rated loads for compo- nents such as suspension, axles and tires.

•Mount equipment base to metal bed or frame of vehicle.

•Follow vehicle manufacture’s instructions.

------------------------------------------------------------------------

AIR VANTAGE® 500 CUMMINS

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 11651 Safety Depends on YouCalifornia Proposition 65 Warnings SafetyIiSAFETY Iii IiiSAFETYPrécautions DE Sûreté IvSAFETYElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Please Examine Carton and Equipment For Damage Immediately ViiOn-Line Product Registration TAbLE of Contents TAbLE of Contents Technical Specifications AIR Vantage 500 Cummins K2325-3 InstallationLocation and Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingOIL PRE-OPERATION Engine and COM- Pressor ServiceFuel USE Diesel Fuel only Fuel CAPMuffler Outlet Pipe AIR Cleaner Inlet HoodSpark Arrestor Welding TerminalsAuxiliary Power Receptacles Remote ControlSTANDbY Power Connections Company Connection of LN-15 to the AIR Vantage 500 Cummins Connection of Lincoln ELEC- Tric Wire FeedersAcross The-Arc Model Control Cable ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the AIR Vantage 500 CumminsGeneral Description OperationRUN Stop Switch Controls and SettingsEngine Temperature Gauge Hour MeterIdler Switch BATTERY Charging LightOIL Pressure Gauge ENGINE PROTECTIONWelding Terminals Switch WELD MODE SELECTOR SWITCHWIRE FEEDER VOLTMETER SWITCH PIN ConnectorAIR Compressor Controls 24 Thru Starting the Engine Engine OperationCold Weather Starting Stopping the EngineWelder Operation ARC Gouging Wire WELDING-CVTable b.3 Typical Current Ranges Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationBOTH 1 and 3 Phase ParallelingOptional Field Installed Accessories AccessoriesTIG Options K2641-2 Four Wheeled STEERAbLE Yard TrailerCompressor Maintenance MaintenanceSingle- and Two-StageEngine Air Cleaners Service InstructionsCooling System Fuel FiltersPreventing Electrical Damage Gfci Receptacle Testing and RESET- Ting Procedure CleaningWelder / Generator MAINTE- Nance Nameplates / Warning Decals MAIN- TenanceTROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionTROUbLESHOOTING Maintenance section of Authorized Field Service Facility Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Dimension Print AIR Vantage 500 Cummins Precaucion Warnung

IM10065 specifications

Air Vent Inc's IM10065 is a notable product in the field of ventilation systems, designed to enhance airflow and maintain optimal indoor air quality. As part of Air Vent's commitment to innovative and effective ventilation solutions, the IM10065 model stands out due to its advanced features and technologies.

One of the primary characteristics of the IM10065 is its efficient design, tailored for use in various residential applications. This product is particularly effective in preventing moisture accumulation within attics, thereby mitigating potential mold growth and ensuring a healthier living environment. By promoting proper ventilation, it helps to regulate temperature and humidity, making it an essential component for any modern home.

The IM10065 employs a reliable polypropylene construction that ensures durability and longevity. This material is not only lightweight but also resistant to corrosion, rust, and weathering, making it suitable for a range of outdoor climates. The robust construction minimizes the risk of damage over time, ensuring that the ventilation system functions optimally throughout its lifespan.

An important aspect of the IM10065 is its installation flexibility. The device can be easily integrated into various roofing types, which simplifies the setup process for contractors and homeowners alike. Moreover, with its low profile design, the IM10065 blends seamlessly into the roofline, preserving the aesthetic appeal of residential properties.

Furthermore, the IM10065 features a unique baffle system that enhances airflow while reducing the chances of backdrafts or wind-driven rain entering the attic space. This innovative feature is pivotal in maintaining consistent airflow, which contributes to the overall energy efficiency of the home.

The IM10065 also includes mesh screening that effectively prevents insects and debris from entering the ventilation system. This protective measure ensures that the internal components remain clean and functional, thereby extending the lifespan of the ventilation system.

In summary, Air Vent Inc's IM10065 is a well-engineered product characterized by its durable materials, flexible installation options, and innovative design features. These attributes make it an excellent choice for homeowners seeking reliable ventilation solutions that promote healthier indoor environments while also contributing to energy efficiency and longevity. With its combination of quality construction and advanced technology, the IM10065 exemplifies the high standards set by Air Vent Inc in the ventilation industry.
Top Page Image Contents