Husqvarna WS 465 manuel dutilisation Mount the saw carriage and saw, Fit the blade

Page 10

ASSEMBLY

Mount the saw carriage and saw

The saw carriage is mounted on the rail at delivery. The carriage can be dismounted from the rail by removing the end stop on the rail and pulling the carriage away.

1Fit the saw body in the saw carriage by lifting the saw body into position. When the saw is lifted into position, the locking handle moves up into an intermediate position. In this position the saw remains in the saw carriage without it needing to be held. However, it is not sufﬁciently secured to begin cutting.

For vertical cuts, the rail must be mounted with the saw carriage lock handle upwards. This to facilitate ﬁtting the saw unit.

2To secure the saw, lift the locking handle towards the saw until the handle locks.

WARNING! To cut without the saw securely

!assembled in the saw carriage and rail is associated with mortal danger.

Fit the blade

WARNING! Never mount or dismount the

!blade or blade guard without ﬁrst switching off the hydraulic unit and disconnecting the hydraulic hoses running to the saw unit.

Carelessness can result in serious personal injury or even death.

On the Husqvarna WS 400-series the blade is ﬁtted in an entirely new way.The new mounting permits, in addition to the tradition way of securing the blade, the possibility to secure the blade radially both quickly and easily:

1Start by removing any dirt from the contact surfaces on the blade ﬂange and blade.

2Check the blade’s direction of rotation. The blade should rotate anticlockwise seen from the saw side and the released part of the diamond should lie in the blade’s direction of rotation. Since the blade rotation direction can be selected, the water spray from the blade can also be selected regardless of how the saw is turned on the rail.

Screw together the outer blade ﬂange, blade and blade ﬂange hub (tightening torque 70-80 Nm).

3Hang the blade with the blade ﬂange and blade ﬂange hub ﬁtted on the cutting arm (blade is not shown in the ﬁgure).

10 – English

Image 10

Contents Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents What is WHAT? What is what on the wall saw?Personal protective equipment Safety InstructionsSteps before using a new wall saw Always use common senseGeneral working instructions General safety precautionsTransport and storage Basic working techniques Cutting of blocksGeneral PresentationComplete saw equipment consists Assembly Mount wall mountings and railMount the saw carriage and saw Fit the bladeFlush cutting Fit the blade guardConnect the hydraulic unit Starting and Stopping Adjusting the guide wheels Settings and AdjustmentsAdjust the saw carriage Maintenance MaintenanceService Daily maintenanceCutting speed, ft/min Technical DataCutting speed, m/s Cutting capacityEC-declaration of conformity Símbolos en la máquina Aclaración DE LOS SímbolosSímbolos en el manual de instrucciones Índice Índice¿QUÉ ES QUÉ? ¿Componentes de la sierra de pared?Equipo de protección personal Instrucciones DE SeguridadEmplee siempre el sentido común Instrucciones generales de trabajo Instrucciones generales de seguridadTransporte y almacenamiento Técnica básica de trabajo Tronzado de bloquesGeneralidades PresentaciónUn equipo de sierra completo consta de Montaje Riel y accesorios del soporte de paredInstalación del carro y de la sierra Monte el discoCorte liso Monte la protección del disco Conecte la unidad hidráulicaArranque Y Parada Ajuste de las ruedas de guía Reglajes Y AjustesAjuste la sierra en el carro Mantenimiento MantenimientoServicio Mantenimiento diarioVelocidad de corte, pies/min Datos TecnicosVelocidad de corte, m/s Capacidad de corteDeclaración CE de conformidad Symbolerklärung Symbole am GerätInhalt InhaltWAS IST WAS? Was ist was an der Wandsäge?Persönliche Schutzausrüstung SicherheitsvorschriftenStets mit gesundem Menschenverstand arbeiten Allgemeine Arbeitsvorschriften Allgemeine SicherheitsvorschriftenTransport und Aufbewahrung Sicherheitsvorschriften Grundlegende Arbeitstechnik Blöcke schneidenAllgemeines VorstellungZu einer kompletten Trennschleiferausrüstung gehören Montage Wandbefestigungen und Schiene montierenSägewagen und Schneideinheit montieren Klinge montierenFlachschneiden Trennscheibenschutz montieren Hydraulikaggregat anschließenStarten UND Stoppen Führungsräder justieren Einstellungen UND JustierungenTrennschleifer im Sägewagen justieren Wartung WartungTägliche Wartung Schnittgeschwindigkeit, ft/min Technische DatenSchnittgeschwindigkeit, m/s SchnittleistungEG-Konformitätserklärung Symboles sur la machine Explication DES SymbolesSymboles dans le manuel Sommaire SommaireQuels Sont LES COMPOSANTS? Quels sont les composants de la scie murale ?Équipement de protection personnelle Instructions DE SécuritéMarche à suivre avant dutiliser une nouvelle scie murale Utilisez toujours votre bon sensMéthodes de travail Instructions générales de sécuritéTransport et rangement Instructions DE Sécurité Techniques de travail de base Découpe de blocsGénéralités PrésentationUn équipement de sciage complet est constitué de Montez les ﬁxations murales et le rail Montez le chariot de sciage et la scie Monter la lameDécoupe à ras Montage du protège-lame Raccordez l’unité hydrauliqueDémarrage ET Arrêt Réglage des roues de guidage RéglagesRéglage de la scie dans le chariot de sciage Entretien EntretienEntretien quotidien Vitesse de coupe, pd/min Caractéristiques TechniquesVitesse de coupe m/s Capacité de coupeAssurance de conformité UE ´z+S/r¶0¨ 2008-03-25´z+S/r¶0¨