Delta 36-714 instruction manual Using Dado Head, Using Auxiliary Wood Facing on RIP Fence

Page 25

USING DADO HEAD

THE BLADE GUARD AND SPLITTER ASSEMBLY CANNOT BE USED WHEN DADOING OR MOULDING. IT MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW AS DESCRIBED IN “USING ACCESSORY MOULDING CUTTERHEAD” SECTION.

AUXILIARY JIGS, FIXTURES, PUSH STICKS AND FEATHER BOARDS SHOULD BE USED.

1.Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. 53). Various combinations of saws and cutters are used to cut grooves from 1/8″ to 13/16″ for use in shelving, making joints, tenoning, grooving, etc. The cutters are heavily swaged and must be arranged so that this heavy portion falls in the gullets of the outside saws, as shown in Fig.

54.The saw and cutter overlap is shown in Fig. 55, (A) being the outside saw, (B) an inside cutter, and (C) a paper washer or washers, used as needed to control the exact width of groove. A 1/4″ groove is cut by using the two outside saws. The teeth of the saws should be positioned so that the raker on one saw is beside the cutting teeth on the other saw.

2.Attach the dado head set (D) Fig. 56, to the saw arbor.

NOTE: THE OUTSIDE ARBOR FLANGE CAN NOT BE USED WITH THE DADO HEAD SET, TIGHTEN THE ARBOR NUT AGAINST THE DADO HEAD SET BODY. DO NOT LOSE THE OUTSIDE ARBOR FLANGE. IT WILL BE NEEDED WHEN REATTACHING A BLADE TO THE ARBOR.

THE ACCESSORY DADO HEAD SET

TABLE INSERT (E) FIG. 56, MUST BE USED IN PLACE OF THE STANDARD TABLE INSERT.

3.Fig. 57, shows a typical dado operation using the miter gage as a guide.

NEVER USE THE DADO HEAD IN A BEVEL POSITION.

ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS COMPLETED.

USING AUXILIARY WOOD FACING ON RIP FENCE

It is necessary when performing special operations such as when using the moulding cutterhead to add wood facing (A) Fig. 58, to one or both sides of the rip fence. Depending on the fence, the wood facing is attached to the fence either with wood screws through holes drilled in the fence (as shown in Fig. 58) or with two clamps. For most work, 3/4" stock is suitable, although an occasional job may require one-inch facing.

Fig. 53

AB

C

Fig. 54

Fig. 55

E

D

Fig. 56

Fig. 57

A

Fig. 58

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Delta 10 Hybrid Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesStay ALERT, Watch What YOU are DOING, Cutting the Workpiece Without the USE Additional Safety Rules for Table SawsMotor Specifications Power ConnectionsGrounding Instructions Extension Cords Functional DescriptionForeword Carton Contents Unpacking and Cleaning AssemblyAssembly Tools Required Bolting the SAW to Floor Disconnect Machine from Power SourceBlade Tilting and Raising Handwheels Installing Drive Belt Do not Operate the SAW Without Right Table Wing Installed S C O N N E C T M a C H I N E F R O M Power SourceExtension Wings Installing the Switch Installing Your Fence SystemAssembling Blade Guard and Splitter Assembly If alignment is necessary, loosen the two screws Aligning Splitter with Blade SAW BladeAdjusting Table Insert Installing Table InsertInstalling Tool Holders Installing Dust PortOperation Locking Switch in OFF PositionAssembling Miter Gage Starting and Stopping SAWBlade Alignment Checking Blade AlignmentBacklash Adjustments Adjusting Blade AlignmentCommon Sawing Operations Miter Gage Operation and AdjustmentCROSS-CUTTING Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGConstructing a Push Stick RippingGuard Removed for CLARITY. Always USE the Guard Using Moulding Cutterhead Using Auxiliary Wood Facing on RIP Fence Using Dado HeadPower Tool Institute TroubleshootingConstructing a Featherboard Constructing a Push Stick PushstickService MaintenanceWarranty AccessoriesPage Page Canadian PORTER-CABLE Delta Service Centers
Top Page Image Contents