Delta 36-714 Additional Safety Rules for Table Saws, Cutting the Workpiece Without the USE

Page 5

ADDITIONAL SAFETY RULES FOR TABLE SAWS

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.ALWAYS USE GUARDS, SPLITTER, AND ANTI- KICKBACK FINGERS whenever possible. Check to see that they are in place, secured, and working correctly.

5.KICKBACK IS THE NATURAL TENDENCY OF THE WORKPIECE TO BE THROWN BACK AT THE OPERATOR when the workpiece initially contacts the blade or if the workpiece pinches the blade. Kickback is dangerous and can result in serious injury.

AVOID KICKBACK by:

A.keeping blade sharp and free of rust and pitch.

B.keeping rip fence parallel to the saw blade.

C.using saw blade guard and spreader for every possible operation, including all through sawing.

D.pushing the workpiece past the saw blade prior to release.

E.never ripping a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

F.using featherboards when the anti-kickback device cannot be used.

G.never sawing a large workpiece that cannot be controlled.

H.never using the fence as a guide when crosscutting.

I.never sawing a workpiece with loose knots or other flaws.

7.REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The vibration of the machine may cause them to move into the saw blade and be thrown out. After cutting, turn the machine off. After the blade has come to a complete stop, remove all debris.

8.NEVER START THE MACHINE with the workpiece against the blade.

9.NEVER run the workpiece between the fence and a moulding cutterhead.

10.CUTTING THE WORKPIECE WITHOUT THE USE OF

A FENCE OR MITER GAUGE IS KNOWN AS “FREEHAND” CUTTING. NEVER perform “free-hand” operations. Use either the fence or miter gauge to position and guide the workpiece.

11.HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.

12.CUTTING COMPLETELY THROUGH THE WORK- PIECE IS KNOWN AS “THROUGH-SAWING”. Ripping and cross-cutting are through-sawing operations. Cutting with the grain (or down the length of the workpiece) is ripping. Cutting across the grain (or across the workpiece) is cross-cutting. Use a fence or fence system for ripping. DO NOT use a fence or fence system for cross-cutting. Instead, use a miter gauge. USE PUSH STICK(S) for ripping a narrow workpiece.

13.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade.

14.KEEP ARMS, HANDS, AND FINGERS away from the blade.

15.NEVER have any part of your body in line with the path of the saw blade.

16.NEVER REACH AROUND or over the saw blade.

17.NEVER attempt to free a stalled saw blade without first turning the machine “OFF”.

18.PROPERLY SUPPORT LONG OR WIDE workpieces.

19.NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the machine is running.

20.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

21.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

22.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Delta 10 Hybrid Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsStay ALERT, Watch What YOU are DOING, General Safety RulesImportant Safety Instructions Cutting the Workpiece Without the USE Additional Safety Rules for Table SawsGrounding Instructions Power ConnectionsMotor Specifications Foreword Functional DescriptionExtension Cords Carton Contents Assembly Tools Required AssemblyUnpacking and Cleaning Blade Tilting and Raising Handwheels Disconnect Machine from Power SourceBolting the SAW to Floor Installing Drive Belt Extension Wings S C O N N E C T M a C H I N E F R O M Power SourceDo not Operate the SAW Without Right Table Wing Installed Installing the Switch Installing Your Fence SystemAssembling Blade Guard and Splitter Assembly If alignment is necessary, loosen the two screws Aligning Splitter with Blade SAW BladeAdjusting Table Insert Installing Table InsertInstalling Tool Holders Installing Dust PortOperation Locking Switch in OFF PositionAssembling Miter Gage Starting and Stopping SAWBlade Alignment Checking Blade AlignmentBacklash Adjustments Adjusting Blade AlignmentCommon Sawing Operations Miter Gage Operation and AdjustmentCROSS-CUTTING Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGGuard Removed for CLARITY. Always USE the Guard RippingConstructing a Push Stick Using Moulding Cutterhead Using Auxiliary Wood Facing on RIP Fence Using Dado HeadConstructing a Featherboard TroubleshootingPower Tool Institute Constructing a Push Stick PushstickService MaintenanceWarranty AccessoriesPage Page Canadian PORTER-CABLE Delta Service Centers
Top Page Image Contents