Delta 36-714 instruction manual Carton Contents

Page 8

CARTON CONTENTS

Fig. 1 Parts

1. Cast Iron Extension

2

	Wings (2)
2.	Switch Assembly
3.	Fence Holder
	Brackets (2)
4.	Drive Belt
5.	Table Insert

1819

17

1

6.	Wrench Hook
7.	Miter Gage Holder
8.	Splitter Mounting
	Bracket
9.	Blade Hex Nut
10.	Blade Flange
11.	10” Carbide-
	Tipped Blade
12.	Blade Wrenches (2)
13.	4mm Hex Wrench
14.	Dust Port
15.	Locking Knobs (2)
16.	Handwheel (2)
17.	Miter Gage
18.	Miter Gage Handle
19.	Splitter/Guard
	Assembly

16	10	8
	10	8
		9
15		3
	11	6
		6
		7

	13		5
		12	4
	14

Fig. 1

Fig. 2 Parts

1. 7/16"-20 x 11/4" Hex Head Screw (6)

2. 7/16" Flat Washer (6)

3. 7/16" Lock Washer (6)

4.M8x30 Hex Head Screw (1)

5.M8 Nut (1)

6.M8 lock washer (1)

7.M8 flat washer (1)

8.M8x25 Hex Head Screw (2)*

9.M8 Washer (2)*

10.M8 Lock Washer (2)*

11.1/4”-20x3/8” Round Head Tap Screw (8)

12.M4 x 10mm Round Head Screw (6)

13.1/4"-20 x 3/4" Hex Head Screw (2)

14.1/4" Flat Washer (2)

15.1/4" Lock Washer (2)

16.5/16"-18 x 5/8 Carriage Head Screw (1)

17.5/16" hex nut (1)

18.5/16" flat washer (1)

19.Nylon Washer (2)

20.M5x20mm Screw (1)

21.Washer for Miter Gage (1)

*Parts 8, 9 and 10 are included to attach the rear rail of the fence to the table of this saw.

	2		5	4	6	7		9	10
			5			7		8	10


1										11
						3
								12
21		20	19		16	17	18	15	14	13
21			19		16	17	18	15	14	13

Fig. 2

8

Image 8

Contents Delta 10 Hybrid Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionStay ALERT, Watch What YOU are DOING, General Safety RulesImportant Safety Instructions Additional Safety Rules for Table Saws Cutting the Workpiece Without the USEGrounding Instructions Power ConnectionsMotor Specifications Foreword Functional DescriptionExtension Cords Carton Contents Assembly Tools Required AssemblyUnpacking and Cleaning Blade Tilting and Raising Handwheels Disconnect Machine from Power SourceBolting the SAW to Floor Installing Drive Belt Extension Wings S C O N N E C T M a C H I N E F R O M Power SourceDo not Operate the SAW Without Right Table Wing Installed Installing Your Fence System Installing the SwitchAssembling Blade Guard and Splitter Assembly If alignment is necessary, loosen the two screws SAW Blade Aligning Splitter with BladeInstalling Table Insert Adjusting Table InsertInstalling Tool Holders Installing Dust PortLocking Switch in OFF Position OperationAssembling Miter Gage Starting and Stopping SAWChecking Blade Alignment Blade AlignmentAdjusting Blade Alignment Backlash AdjustmentsMiter Gage Operation and Adjustment Common Sawing OperationsNever USE the Fence AS a CUT-OFF Gage When CROSS-CUTTING CROSS-CUTTINGGuard Removed for CLARITY. Always USE the Guard RippingConstructing a Push Stick Using Moulding Cutterhead Using Dado Head Using Auxiliary Wood Facing on RIP FenceConstructing a Featherboard TroubleshootingPower Tool Institute Pushstick Constructing a Push StickMaintenance ServiceAccessories WarrantyPage Page Canadian PORTER-CABLE Delta Service Centers