WARNING: ALWAYS wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
WARNING: ALWAYS use proper eye protection. All users and bystanders must wear proper eye protection that conforms to ANSI Z87.1.
WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS wear certified safety equipment:
•ANSI Z87.1 eye protection (CAN/CPA Z94.3),
•ANSI S12.6 (S3.19) hearing protection,
•NOSH/OSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known in the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. Always operate tool in
SYMBOLS
The label on your tool may include the following symbols. The symbols and their definitions are as follows:
V | volts | A | amperes | ||||||
Hz | hertz | W | watts | ||||||
min | minutes | no | alternating current | ||||||
|
|
|
| direct current | no load speed | ||||
|
|
|
| ||||||
|
|
|
| Class I Construction |
|
|
|
| earthing terminal |
|
|
| ................. |
|
|
| .................. | ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
| (grounded) |
|
|
| ................. | safety alert symbol |
|
|
| ................. | Class II Construction | .../min or rpm... | revolutions or | |||
|
|
|
| (double insulated) |
|
|
|
| reciprocation per minute |
|
|
|
| ............ Read instruction manual before use | Use proper respiratory protection | ||||
|
|
| ................. | Use proper eye protection |
|
|
| .................. | Use proper hearing protection |
When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
|
|
| Minimum Gauge for Cord Sets |
| ||
Volts |
| Total Length of Cord in Feet | ||||
120V |
| |||||
240V |
| |||||
| ||||||
|
|
| ||||
Ampere Rating | American Wire Gauge |
| ||||
More | Not more |
| ||||
Than | Than | 18 | 16 | 16 | 14 | |
0 | - | 6 | ||||
6 | - | 10 | 18 | 16 | 14 | 12 |
10 - | 12 | 16 | 16 | 14 | 12 | |
12 - | 16 | 14 | 12 | Not Recommended | ||
|
|
|
|
|
|
|
4