Carrier 592-085 warranty Applications, NEW Construction, Retrofit/Replacement, Carrier Warranty

Page 3

APPLICATIONS

Whether you are designing a new structure or replac- ing packaged terminal air conditioning units in an existing building, Carrier will meet your needs.

Hotels and motels

Nursing homes and assisted living care centers

Offices

Apartments

Single-family dwellings

Home conversions and residential add-ons

NEW CONSTRUCTION

The Carrier 52P and 52C Packaged Terminal Air Con- ditioning (PTAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit instal- lation, Carrier’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

ADVANTAGES FOR NEW CONSTRUCTION Design Flexibility For The Architect/Engineer

Super-quiet performance, indoors and out

No bulky duct system

No separate equipment room

No water towers or additional cooling equipment

No complex match-up of different HVAC components

Less sensitivity to building orientation (sun, wind, shade)

Optional architectural grille to permit custom exte- rior appearance

Initial Cost Savings For The Building Owner

No expensive component HVAC system purchase

No equipment room or maintenance engineering staff

Two-part delivery to minimize on-site damage

Weather-protected wall sleeve that goes in place during construction; chassis that slides in place after construction

No seasonal changeover required for cooling or heating — units are self-contained comfort systems

Lower Operating Costs And Reliable Comfort For The Occupant

Heat pump models offer substantial savings over models with conventional electric resistance heaters

Individual units allow tenants to choose the degree of comfort and operating economy.

Rapid servicing reduces downtime: complete chas- sis can be replaced in minutes without disrupting other occupants.

Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

Replace the existing wall sleeve with a Carrier Weather Last™ sleeve. See accessory sleeve sec- tion for selecting the correct sleeve for your appli- cation. Note, in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

Use an existing sleeve and exterior grille. The Carrier 52P and 52C series PTAC will fit into most major competitors wall sleeves/grilles, including GE, Amana, Trane, Bryant, Carrier 52S and Carrier 52B, and NO accessory retrofit kit is required. Carrier units will also retrofit into Friedrich T series and ZoneAire wall sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

IMPORTANT: All other sleeve or exterior grille retrofit applications need prior approval from Carrier. Please contact your Carrier representative for assistance.

CARRIER WARRANTY

Carrier’s five-year warranty is the most comprehen- sive in the industry. Carrier provides:

Full coverage for parts and labor for first year.

Four additional years of full coverage on sealed refrigeration systems.

Limited second through fifth year coverage on non- refrigeration system parts.

3

Image 3
Contents Architects and ENGINEERS’ Manual ContentsPage NEW Construction RETROFIT/REPLACEMENTCarrier Warranty ApplicationsOversizing ApplicationsApplication Considerations UndersizingProduct Overview 52P and 52C Fan Cycle Switch Dual optionsEfficient FAN Motor Product Features and Benefits 52P and 52CQuiet Operation Most Efficient PerformanceNO-RUST Weather Last Wall Sleeve and Front Panel Removable Front PanelANTI-THEFT Knobs BI-DIRECTIONAL Discharge Grille Product Features and BenefitsTWO-PIECE Lifetime Indoor Filter Washable Vent AIR FilterPower Cord for 265-V Units BI-MOLDED Condenser ShroudSnow Baffle Hidden Controls Easy Access to ChassisTemperature Limiter and Control Knob Fan Cycle SwitchCondensate Removal System Enhanced Copper TubingSeamless Basepan Condensate Drain ValveSpecial Features Heat Pumps PAY Their OWN WAYHow The Heat Pump Works Cooling Electric Premium Zone Capacity Heat Pump Energy SavingsNumber Ordering Data 52P and 52CFACTORY-INSTALLED Options 52P and 52C Wall Thermostat Control RC,RPCorrosion Protection CP,RP Wall Sleeves FIELD-INSTALLED Accessories 52P and 52CClimate Master Wall Sleeve Adapter Insulated Metal Wall SleevesWall Sleeve Molding Kit Friedrich and ZoneAire Retro- fit Wall Sleeve AdapterPolymeric Architectural Outdoor Grilles Louvered FIELD-INSTALLED Accessories 52P and 52COutdoor Grilles Aluminum Architectural Outdoor Grilles LouveredHardwire Kit Outdoor Grille SelectionConduit Interface Kit Non-electrical subbase SubbaseSubbase Power Disconnect Switch Leveling legsSubbase Fuse Kit Manual Changeover Wall Thermostat ThermostatsDigital Programmable Thermostat Non-Programmable ThermostatWall Thermostat Interface Retrofit Kit Speed Fan Control from Wall ThermostatThermostat Locking Cover Lateral Duct Kit Condensate Drain KitSecurity Door Kit Power Vent with Power Door KitLateral Air Deflector Curtain DeflectorEnergy Management Kit Replacement FiltersDimension Drawings and Installation Data NEW Construction Typical Wall Installation208/230-V Units Dimension Drawings and Installation Data NEW Construction Typical Wall Installation Minimum Clearance for Indoor Outdoor Discharge AIR Typical Lateral Duct Installation Electrical Connections 52P and 52C with SubbaseWall Thermostat Connections Model 52PQ 230/208-1-60 Product Data 52P265 Model 52PQCAPACITY* Btuh 52PQ Rev. CycleModel 52PC and PE 230/208-1-60 Product Data 52PModel 52PC and PE Rev. Cyc Product Data 52CModel 52CQ 230/208-1-60 Cooling Heating 52CQHeating Cooling 52CQ Rev. Cycle Model 52CQ52CE Product Data 52CModel 52CE 230/208-1-60 Heating† Cooling52CE Volts Model 52CEEvaporator entering air temp. 80 F Evap. air 350 CFM Expanded Ratings Data 52P and 52CCooling Performance Evaporator entering air temp. 80 F Evap. air 260 CFMCooling Performance Cooling Sensible Heat Factors SHF AT 80 F Indoor DBEvaporator entering air temp. 80 F Evap. air 320 CFM Sound Data 52P and 52C Indoor Sound Data 52P and 52CSound Transmission Class STC = SLS Wiring Diagrams 52P and 52C‘R’ 24 VAC Output Power to Wall ‘C’ Common Thermostat Wiring Diagrams 52P and 52CPage Wiring Diagrams 52P and 52C Maximum Length ft Following are recommended wire sizesMaster Ptac Unit O C ’STAT Hvac Guide Specifications Guide SpecificationsGuide Specifications Page Carrier Typical WarrantyCarrier Corporation Accessory Form Number Part Number Description Accessory List

592-085 specifications

The Carrier 592-085 is a leading-edge commercial air conditioning unit designed to provide efficient cooling solutions for various business environments. Known for its reliability, performance, and advanced technology, the Carrier 592-085 has become a popular choice among facility managers and HVAC professionals alike.

One of the primary features of the Carrier 592-085 is its impressive cooling capacity, which can handle large spaces with ease. The unit operates effectively in various climates, maintaining optimal indoor temperatures even during the hottest summer months. With a cooling capacity rating of 8.5 tons, it can accommodate medium to large commercial spaces, ensuring comfort for employees and customers.

The unit is equipped with advanced inverter technology, which allows it to adjust cooling output based on real-time demand. This not only enhances energy efficiency but also leads to significant cost savings over time. The inverter-driven compressor operates silently, reducing noise levels without compromising on performance.

In addition to its energy-efficient capabilities, the Carrier 592-085 features highly innovative refrigerant management. The unit uses R-410A refrigerant, which is environmentally friendly and contributes to reducing ozone depletion. This makes it an ideal choice for businesses looking to minimize their ecological footprint while maintaining effective cooling.

The Carrier 592-085 also boasts durable construction, with weather-resistant materials designed to withstand harsh external conditions. This ensures longevity and reduces maintenance needs in the long run. The unit's design also includes access panels for convenient servicing, making it easier for technicians to perform routine maintenance and repairs.

Moreover, the Carrier 592-085 is compatible with advanced building management systems, allowing for seamless integration into existing operations. Features such as remote monitoring and control provide users with the flexibility to manage their HVAC systems efficiently, enhancing overall operational efficiency.

In summary, the Carrier 592-085 stands out in the commercial air conditioning market due to its robust performance, energy efficiency, and advanced features. From its inverter technology to eco-friendly refrigerant usage and durable design, this unit provides a comprehensive solution for those seeking reliable cooling in commercial settings. It represents a smart investment for businesses that prioritize both comfort and sustainability.