Craftsman 113.29921 owner manual Unpacking and Checking Contents

Page 10

Unpacking and Checking Contents

Tools Needed

Combination Square must be true. Check it's accuracy as shown below.

Utility Knife

Phillips Screwdriver

Tape Rule

Draw light line on board along edge

I i

LI

Select the straight edge of 314" thick board. This edge must be perfectly straight.

straight edge are used to

align the saw, They must NOTE: The square and be accurate if the saw is

to be aligned properly,

Medium Screwdriver

Small Screwdriver

\

Should be no gap or overlap here when square is flipped over in dotted position,

	Combination	Wrenches		_.,	Combination
	3!8 ino,7116 In,,	112 Ino, 9/16	In.	_.,	Combination
	3!8 ino,7116 In,,	112 Ino, 9/16	In.
					Square
					,_',',i- '.;:: '. 'I._,t
	Hex "L" Wrenches
	3/16 In., 1/8 In,			Framing Square

Unpacking

1 Separate saw and all parts from packing materials and check each one with the illustration and the "List of Loose Parts" to make certain all items are accounted for, before discarding any packing material

WARNING: If any parts are missing, do not attempt to assemble the table saw, plug in the power cord or turn the switch on until the missing parts are obtained and are installed correctly.

WARNING: The saw is heavy° To avoid back injury, get help to lift the saw. Hold the saw close to your body. Bend your knees so you can lift with your legs, not your back.

WARNING: For your own safety, never connect plug to power source outlet until all assembly steps are complete, and you have read and under- stand the safety and operating instructions.

NOTE: Before beginning assembly:

o Check that all parts are included If you are missing any part, do not assemble the saw Contact your Sears Ser- vice Center to get the missing part

o Sometimes small parts can get lost in packaging mate* riat Do not throw away any packaging until saw is put together Check packaging for missing parts before contacting Sears

o A complete parts list (Repair Parts) is at the end of the manual Use this list to identify the part number of the missing part

10

Image 10

Contents Sears, Roebuck and Co., Hoffman Estates, IL US,A Two Table ExtensionsRip Fence Miter Gauge Save This Manual For Future ReferenceWhen Installing Or Moving The Saw Safety Instructions For Table SawSafety Signal Words Before Using The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, ILBefore Each Use Plan Ahead To Protect Your Eyes, Hands, Face and Ears Safety Instructions For Table SawsDress for safety Whenever Sawblade Is SpinningGrain Additional Safety InstructionsWhile Thru-sawing FeatherboardMiter Cut Glossary of Terms for WoodworkingMolding Properly Prong Plug Grounded Prong Outlet Motor Specifications110-120Volt, 60 Hz. Tool Information Make sure thisExtension Wire Sizes Required Cord Length For A.W.G Motor Specifications and ElectricalWire Sizes RequirementsContents Unpacking and Checking Contents Parts ListLoose Loose PartsInstalling Handwheels and Bevel Pointer Assembling Steel LegsLeg Set Flat Washer Mounting Your SawBench Mounting Assembly Assembling Table ExtensionsInstalling Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas herCould be hit or cut Wire TieAligning Extensions ExtensionChecking Table Insert Leveling Tab EdgeInstalling Blade Guard Port AndBracket To Rip Fence On-Off SwitchGetting to Know Your Table Saw Exacti-Cut Table Insert Tilt Handwheel Elevation HandwheelLock Knob Removing and Installing Sawblade Push To TighenInspect your saw Safety Instructions for Basic Saw OperationsBefore Each Use Inspect Your BladeAvoid Accidental Starting Planyour cutDont Force Tool Push Stick Work Feed DevicesPush Block 3E-l!2rL Thick Plywood Base Auxiliary FenceMaking the handle Thick Side Plywood Finished Auxiliary FenceBasic Saw Operations Using the Miter GaugeAdditional Safety Instructions for Crosscutting CrosscuttingCrosscutting Bevel Crosscutting Miter CrosscuttingCompound Crosscutting Ripping Using the Rip FenceAdditional Safety instructions for Rip Cuts Always Support Long Or Wide WorkpiecesPush Block Work Using Featherboards for Thru-SawingBevel Ripping Narrow Work Featherhoar FacingWork Sup Using Featherboards for Non Thru-SawingResawing Ond passFence LcelSaeJArbor MakingPloughing and Molding AdjustmentsMended accessories Molding CuttingSelf Aligning Spring Adjustment Rip FenceSlide Spring To Adjust Pressure Rip Fence Alignment AdjustmentAdjusting Rip Scale Indicator Lock HandleLocking screws To check for parallelism3t16 WrenchPointer Adjusting Screw Blade Tilt, or Squareness of Blade to TableWith Piece Tilt Screw Blade ElevationTilt and Elevation Mechanism ScrewsMaintenance Maintaining Your Table SawLubrication Pivot NutSears Recommends the Following Accessories RemedyProbable Cause Into bladeRepair Parts Parts List for Craftsman 10 Inch Fable Saw Model NoParts List for Craftsman 10 Inch Table Saw Model No 201Parts List for Craftsman 10 Inch Table Saw Model No. t DescriptionParts list for Craftsman 10 Inch Table Saw 201!17Parts List for Craftsman 10 Inch Table Saw Model Key Pad No DescriptionRepair Parts Parts List for Craftsman 10 Inch Table Saw ModelRear Guide Bar Ref Model NoKey Key j Foot LevelingSears, Roebuck For the repair or replacement paris you needFor in-home major brand repair service Co., Hoffman Estates, IL U.S.A