Craftsman 113.29921 owner manual Hex Nuts Lockwashers, Lockwas her

Page 16

Assembly (continued)

3 Mount switch to front guide bar with two 5/16-!8 x 3/4 hex head screws, tour lockwashers and two nuts_ Securely tighten both nuts

Hex Nuts

,, 1 Lockwashers

4Place front guide bar against saw table and drop it in place engaging the screws in the slots, Make sure the spacers are between the front guide bar and the table

5End of front guide bar must be 7-5/16 inch from side of saw table, This is important so that rip fence indi- cator can be aligned

6With the blade of your combination square set to 1/4 inch, gauge and adjust front guide bar so the edge of the bar is 1/4 inch above the edge of the table, Securely tighten nuts,

7Install 5/16-18 x 1-1/2 hex head screw through the fourth slot in front guide bar (that lines up with

bracket), through the 1/4 inch spacer and the bracket, Install a 5/16 inch external lockwasher and 5/16-t8

hex jam nut,

_'_ _ Loekwashers

3/4 In.

Hex Head Screws

Lockwasher Hex Nut

1-1/2 In.

Hex Head Screw

@ 7-5!16 no

8.Remove the two truss head screws from rear of right table extension,

9 Attach the rear guide bar in a similar manner to the front guide bar Make sure that the end of the bar is 11 inches from the side of the saw table, Spacers are not required

10 Reinstall two truss head screws, tockwashers and hex nuts removed in step 8. Check that all hardware is tight

11insert 5/16-18 x 1 hex head screw through the eighth slot in rear guide bar and bracket, Install 5/16 exter- nal Iockwasher and 5/16 hex jam nut Tighten securely

Hex Nut

Lockwas her'

t In,

Hex Head

Screw

Truss Head

Screws

1 In. Hex Head

Screws

16

Image 16

Contents Two Table Extensions Rip Fence Miter GaugeSears, Roebuck and Co., Hoffman Estates, IL US,A Save This Manual For Future ReferenceSafety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, ILBefore Each Use Safety Instructions For Table Saws Dress for safetyPlan Ahead To Protect Your Eyes, Hands, Face and Ears Whenever Sawblade Is SpinningAdditional Safety Instructions While Thru-sawingGrain FeatherboardMiter Cut Glossary of Terms for WoodworkingMolding Motor Specifications 110-120Volt, 60 Hz. Tool InformationProperly Prong Plug Grounded Prong Outlet Make sure thisMotor Specifications and Electrical Wire SizesExtension Wire Sizes Required Cord Length For A.W.G RequirementsContents Unpacking and Checking Contents List LooseParts Loose PartsInstalling Handwheels and Bevel Pointer Assembling Steel LegsLeg Set Flat Washer Mounting Your SawBench Mounting Assembly Assembling Table ExtensionsInstalling Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas herWire Tie Aligning ExtensionsCould be hit or cut ExtensionChecking Table Insert Leveling Tab EdgeInstalling Blade Guard Port AndBracket To On-Off Switch Getting to Know Your Table SawRip Fence Exacti-Cut Table Insert Tilt Handwheel Elevation HandwheelLock Knob Removing and Installing Sawblade Push To TighenSafety Instructions for Basic Saw Operations Before Each UseInspect your saw Inspect Your BladeAvoid Accidental Starting Planyour cutDont Force Tool Push Stick Work Feed DevicesPush Block Auxiliary Fence Making the handle3E-l!2rL Thick Plywood Base Thick Side Plywood Finished Auxiliary FenceUsing the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations CrosscuttingCrosscutting Bevel Crosscutting Miter CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety instructions for Rip CutsRipping Always Support Long Or Wide WorkpiecesPush Block Using Featherboards for Thru-Sawing Bevel Ripping Narrow WorkWork Featherhoar FacingUsing Featherboards for Non Thru-Sawing ResawingWork Sup Ond passLcelSaeJ ArborFence MakingAdjustments Mended accessoriesPloughing and Molding Molding CuttingSelf Aligning Spring Adjustment Rip FenceRip Fence Alignment Adjustment Adjusting Rip Scale IndicatorSlide Spring To Adjust Pressure Lock HandleTo check for parallelism 3t16Locking screws WrenchPointer Adjusting Screw Blade Tilt, or Squareness of Blade to TableWith Piece Blade Elevation Tilt and Elevation MechanismTilt Screw ScrewsMaintenance Maintaining Your Table SawLubrication Pivot NutSears Recommends the Following Accessories RemedyProbable Cause Into bladeRepair Parts Parts List for Craftsman 10 Inch Fable Saw Model NoParts List for Craftsman 10 Inch Table Saw Model No 201Parts List for Craftsman 10 Inch Table Saw Model No. t DescriptionParts list for Craftsman 10 Inch Table Saw 201!17Parts List for Craftsman 10 Inch Table Saw Model Key Pad No DescriptionRepair Parts Parts List for Craftsman 10 Inch Table Saw ModelRear Guide Bar Ref Model NoKey Key j Foot LevelingFor the repair or replacement paris you need For in-home major brand repair serviceSears, Roebuck Co., Hoffman Estates, IL U.S.A