Craftsman 113.29921 owner manual Blade Elevation, Tilt and Elevation Mechanism, Tilt Screw, Screws

Page 42

Adjustments (continued)

Blade Elevation

When the eIevation handwheel is turned clockwise, until it stops, the blade must not be more that 2-5/8 inches above the table If the b}ade extends more than 2-5/8 inches, the motor could interfere with the underside of the table causing misalignment,

With the blade extending 2-5/8 inches above the table, the stop collar and spacer must be against the elevation screw pivot nut If the blade extends more that 2-5/8 inches, loosen two screws in stop collar, and readjust it,

Tilt and Elevation Mechanism

The handwheels should turn freely without binding, The turning action can be adjusted by tighten{ng or loosening the screws in the bearing retainer Both handwheels must be removed to reach the adjusting screws

f

Tilt Screw

Tilt

Handwheel

Step

Elevation

Spacer

!

I

"Elevation Screw

Pivot Nut

1

Tilt Screw

Pivot Nut

Elevation

NOTE: When adjusting the screws on the tilt bearing retainer, ho_d the nut inside using a 3/8" wrench, The screws for the elevation bearing retainer can be reached with a small screwdriver through the curved slot on the front of the saw

_'_ _-_Handwheel

Adjust	Thes_	!	,_'_-,,_J_
Two	Screws	_	_OJ F[_

Adjust These

Two Screws

42

Image 42

Contents Sears, Roebuck and Co., Hoffman Estates, IL US,A Two Table ExtensionsRip Fence Miter Gauge Save This Manual For Future ReferenceWhen Installing Or Moving The Saw Safety Instructions For Table SawSafety Signal Words Before Using The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, ILBefore Each Use Plan Ahead To Protect Your Eyes, Hands, Face and Ears Safety Instructions For Table SawsDress for safety Whenever Sawblade Is SpinningGrain Additional Safety InstructionsWhile Thru-sawing FeatherboardGlossary of Terms for Woodworking Miter CutMolding Properly Prong Plug Grounded Prong Outlet Motor Specifications110-120Volt, 60 Hz. Tool Information Make sure thisExtension Wire Sizes Required Cord Length For A.W.G Motor Specifications and ElectricalWire Sizes RequirementsContents Unpacking and Checking Contents Parts ListLoose Loose PartsInstalling Handwheels and Bevel Pointer Assembling Steel LegsMounting Your Saw Leg Set Flat WasherBench Mounting Assembly Assembling Table ExtensionsInstalling Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas herCould be hit or cut Wire TieAligning Extensions ExtensionChecking Table Insert Leveling Tab EdgeInstalling Blade Guard Port AndBracket To Rip Fence On-Off SwitchGetting to Know Your Table Saw Exacti-Cut Table Insert Tilt Handwheel Elevation HandwheelLock Knob Removing and Installing Sawblade Push To TighenInspect your saw Safety Instructions for Basic Saw OperationsBefore Each Use Inspect Your BladePlanyour cut Avoid Accidental StartingDont Force Tool Work Feed Devices Push StickPush Block 3E-l!2rL Thick Plywood Base Auxiliary FenceMaking the handle Thick Side Plywood Finished Auxiliary FenceBasic Saw Operations Using the Miter GaugeAdditional Safety Instructions for Crosscutting CrosscuttingCrosscutting Miter Crosscutting Bevel CrosscuttingCompound Crosscutting Ripping Using the Rip FenceAdditional Safety instructions for Rip Cuts Always Support Long Or Wide WorkpiecesPush Block Work Using Featherboards for Thru-SawingBevel Ripping Narrow Work Featherhoar FacingWork Sup Using Featherboards for Non Thru-SawingResawing Ond passFence LcelSaeJArbor MakingPloughing and Molding AdjustmentsMended accessories Molding CuttingSelf Aligning Spring Adjustment Rip FenceSlide Spring To Adjust Pressure Rip Fence Alignment AdjustmentAdjusting Rip Scale Indicator Lock HandleLocking screws To check for parallelism3t16 WrenchPointer Adjusting Screw Blade Tilt, or Squareness of Blade to TableWith Piece Tilt Screw Blade ElevationTilt and Elevation Mechanism ScrewsMaintenance Maintaining Your Table SawLubrication Pivot NutSears Recommends the Following Accessories RemedyProbable Cause Into bladeRepair Parts Parts List for Craftsman 10 Inch Fable Saw Model NoParts List for Craftsman 10 Inch Table Saw Model No 201Parts List for Craftsman 10 Inch Table Saw Model No. t DescriptionParts list for Craftsman 10 Inch Table Saw 201!17Parts List for Craftsman 10 Inch Table Saw Model Key Pad No DescriptionRepair Parts Parts List for Craftsman 10 Inch Table Saw ModelModel No Rear Guide Bar RefKey Key j Foot LevelingSears, Roebuck For the repair or replacement paris you needFor in-home major brand repair service Co., Hoffman Estates, IL U.S.A