Craftsman 113.29921 owner manual Assembly, Assembling Table Extensions

Page 14

Assembly (continued)

Assembling Table Extensions

1 From the bag labeled "Table Extensions" remove the following hardware: (Quantity indicated is for two extensions)

*8 Hex Head Screws, 5/16-18 x 1-1/4" Long *8 Flat Washers, 21/64 x 5/8 x 1/16

*8 Lockwashers. 5/16" External Type

*8 Hex Nuts, 5/16-18

"10 Truss Head Screw, 1/4-20 x 1

"10 Hex Nut, 1/4-20

"10 Lockwashers, 1/4 External Type

*4 Flat Washers, 1/7/64 x 3/4 x 1/16

2 Brackets

From the bag labeled "Large Parts" remove only the fol- lowing:

4 Comer Support Brackets

From among the loose parts find the following: 2 Table Extensions

items marked with asterisk (*) are shown actual size

2 Assemble with saw upside down

NOTE: To protect the finished surfaces of the saw and extensions, lay a piece of heavy paper or cardboard on the floor..

WARNING: Stock table extensions must be installed. They help support the fence guide bars.

An unsupported guide bar can twist. Twisted guide bars can misalign fence. A misaligned fence can cause binding or kickback. You could be hit or

cut,

3Install corner support brackets, 1/4-20 x 1 inch truss head screws, 17/64 inch flat washers, 1/4 inch exter- nal Iockwashers and 1/4-20 hex nuts as shown, Hand

tighten onty

4insert four (4) 5/16-18 x 1-1/4 inch long hex head

screws through the holes on inside edge of one extension

5Instal! 21/64 ID fiat washer, 5/16 external lock- washer, and 5/16-t8 hex nut on the end of each screw Just start nut on end of screw

6Slide the extension with hardware into four slots in side of table Line up front edge of extension with front edge of table and tighten all screws and nuts

7Repeat for other extension

t4

		.... i	,,,
Hex Head Screw		21_41,D.	O
0			5/16 In External
		Flat Washer

			Lockwasher
	@Q
5/16-18			©
Hex Nut			114 In External

17/64 I,D. Hex Nut Lock'washer

Flat Washer

Truss Head Screw

Bracket

s°ppc

	17/64		I.D.
	Flat Washer
	\	1/4-20
	\	Hex Nut
Corner	_._\	/		(_
support			Lockwasher	Table
Bracket	----__k' _'-4z.z_

This Edge Toward Table

5/16-18

Hex Nut _

51'16Lock'washer

21/64 I.D.

Flat Washer

Hex Head

Screw

Image 14

Contents Sears, Roebuck and Co., Hoffman Estates, IL US,A Two Table ExtensionsRip Fence Miter Gauge Save This Manual For Future ReferenceWhen Installing Or Moving The Saw Safety Instructions For Table SawSafety Signal Words Before Using The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, ILBefore Each Use Plan Ahead To Protect Your Eyes, Hands, Face and Ears Safety Instructions For Table SawsDress for safety Whenever Sawblade Is SpinningGrain Additional Safety InstructionsWhile Thru-sawing FeatherboardMolding Glossary of Terms for WoodworkingMiter Cut Properly Prong Plug Grounded Prong Outlet Motor Specifications110-120Volt, 60 Hz. Tool Information Make sure thisExtension Wire Sizes Required Cord Length For A.W.G Motor Specifications and ElectricalWire Sizes RequirementsContents Unpacking and Checking Contents Parts ListLoose Loose PartsInstalling Handwheels and Bevel Pointer Assembling Steel LegsBench Mounting Mounting Your SawLeg Set Flat Washer Assembly Assembling Table ExtensionsInstalling Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas herCould be hit or cut Wire TieAligning Extensions ExtensionChecking Table Insert Leveling Tab EdgeInstalling Blade Guard Port AndBracket To Rip Fence On-Off SwitchGetting to Know Your Table Saw Exacti-Cut Table Insert Tilt Handwheel Elevation HandwheelLock Knob Removing and Installing Sawblade Push To TighenInspect your saw Safety Instructions for Basic Saw OperationsBefore Each Use Inspect Your BladeDont Force Tool Planyour cutAvoid Accidental Starting Push Block Work Feed DevicesPush Stick 3E-l!2rL Thick Plywood Base Auxiliary FenceMaking the handle Thick Side Plywood Finished Auxiliary FenceBasic Saw Operations Using the Miter GaugeAdditional Safety Instructions for Crosscutting CrosscuttingCrosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Ripping Using the Rip FenceAdditional Safety instructions for Rip Cuts Always Support Long Or Wide WorkpiecesPush Block Work Using Featherboards for Thru-SawingBevel Ripping Narrow Work Featherhoar FacingWork Sup Using Featherboards for Non Thru-SawingResawing Ond passFence LcelSaeJArbor MakingPloughing and Molding AdjustmentsMended accessories Molding CuttingSelf Aligning Spring Adjustment Rip FenceSlide Spring To Adjust Pressure Rip Fence Alignment AdjustmentAdjusting Rip Scale Indicator Lock HandleLocking screws To check for parallelism3t16 WrenchPointer Adjusting Screw Blade Tilt, or Squareness of Blade to TableWith Piece Tilt Screw Blade ElevationTilt and Elevation Mechanism ScrewsMaintenance Maintaining Your Table SawLubrication Pivot NutSears Recommends the Following Accessories RemedyProbable Cause Into bladeRepair Parts Parts List for Craftsman 10 Inch Fable Saw Model NoParts List for Craftsman 10 Inch Table Saw Model No 201Parts List for Craftsman 10 Inch Table Saw Model No. t DescriptionParts list for Craftsman 10 Inch Table Saw 201!17Parts List for Craftsman 10 Inch Table Saw Model Key Pad No DescriptionRepair Parts Parts List for Craftsman 10 Inch Table Saw ModelKey Model NoRear Guide Bar Ref Key j Foot LevelingSears, Roebuck For the repair or replacement paris you needFor in-home major brand repair service Co., Hoffman Estates, IL U.S.A