Craftsman 113.29921 owner manual Installing Rip Fence Guide Bars and Switch

Page 15

8Inserta 1/4-20x 1trussheadscrewthroughbottom holein thebracket,andthroughthefirstholein the

righthandextensionInstalla. lockwasherandnuton thescrewHandtightenthenut

NOTE:Whensawis upsidedown,righthandextension isontheleftsidewhenfacingfrontofsaw

9Inserta 1/4-20x 1trussheadscrewthroughbottom

holein the other bracket and the fourth hole of the

extension Install a Iockwasher and nut on the screw

Hand tighten the nut.

jFront of Saw

1/4-20

Hex Nut1/4

_ ¢._----Lockwasher

1st Hole

Bracket

Truss Hd. Screws

Installing Rip Fence Guide Bars and Switch

Box

1.From the bag labeled "Guide Bars" remove the fol- lowing hardware:

*3 Hex Head Screws, 5/16-18 x 1-t/2

*3 Hex Head Screws, 5/16-I8 x 1

*6 Hex Jam Nuts, 5/I6-18

*4 Flat Washers, 21/64 x 5/8 x 1/16

*3 Spacers, 3/4 dia, x 1/2 long

*6 Lockwashers, 5/16 External Type

From the bag labeled "Miscellaneous" remove only the following hardware:

*2 Hex Head Screws, 5/16-18 x 3/4

*2 Hex Jam Nuts, 5/16-18

*4 Lockwashers, 5/t6 External Type From among the loose parts find the following:

1Front Guide Bar

1Rear Guide Bar

Items marked with asterisk (*) are shown actual size

5/16-18 x 3/4	5/16 In. External	G
5/16-18 x 3/4
Hex Hd. Screw		5/16 In.
	Lockwashers	Hex Jam Nut
		Hex Jam Nut

5116-18 x	1-1/2 In	5/16-18 x 1 In.
Hex Hd.	Screw	Hex Hd. Screw

21164 In.	1/2 In. Spacer
Washer

2.Position guide bars on floor and install hardware as shown,. Just start the nuts on the end of the screws, do not screw nuts on all the way,

(For Mounting __'_

ToBracko,

1-112 ln.Hex Head Screw

8th Slot (For Mounting

To Bracket)

/Rear Guide Bar

,	¢	3rd Slot	1 In Hex
• FI_	_	3rd Slot	Head'Screw
wasner.._	__	l
Hex Nut	__--_

2rid Slot t_'_ ._ / Flat Washer

1st SIo_t I Spacer

Front Guide Bar

15

Image 15

Contents Save This Manual For Future Reference Two Table ExtensionsRip Fence Miter Gauge Sears, Roebuck and Co., Hoffman Estates, IL US,ASears, Roebuck and Co, D/817 WA Hoffman Estates, IL Safety Instructions For Table SawSafety Signal Words Before Using The Saw When Installing Or Moving The SawBefore Each Use Whenever Sawblade Is Spinning Safety Instructions For Table SawsDress for safety Plan Ahead To Protect Your Eyes, Hands, Face and EarsFeatherboard Additional Safety InstructionsWhile Thru-sawing GrainGlossary of Terms for Woodworking Miter CutMolding Make sure this Motor Specifications110-120Volt, 60 Hz. Tool Information Properly Prong Plug Grounded Prong OutletRequirements Motor Specifications and ElectricalWire Sizes Extension Wire Sizes Required Cord Length For A.W.GContents Unpacking and Checking Contents Loose Parts ListLoose PartsAssembling Steel Legs Installing Handwheels and Bevel PointerMounting Your Saw Leg Set Flat WasherBench Mounting Assembling Table Extensions AssemblyInstalling Rip Fence Guide Bars and Switch Lockwas her Hex Nuts LockwashersExtension Wire TieAligning Extensions Could be hit or cutLeveling Tab Edge Checking Table InsertInstalling Blade Guard Port AndBracket To Exacti-Cut Table Insert Tilt Handwheel Elevation Handwheel On-Off SwitchGetting to Know Your Table Saw Rip FenceLock Knob Push To Tighen Removing and Installing SawbladeInspect Your Blade Safety Instructions for Basic Saw OperationsBefore Each Use Inspect your sawPlanyour cut Avoid Accidental StartingDont Force Tool Work Feed Devices Push StickPush Block Thick Side Plywood Finished Auxiliary Fence Auxiliary FenceMaking the handle 3E-l!2rL Thick Plywood BaseCrosscutting Using the Miter GaugeAdditional Safety Instructions for Crosscutting Basic Saw OperationsCrosscutting Miter Crosscutting Bevel CrosscuttingCompound Crosscutting Always Support Long Or Wide Workpieces Using the Rip FenceAdditional Safety instructions for Rip Cuts RippingPush Block Featherhoar Facing Using Featherboards for Thru-SawingBevel Ripping Narrow Work WorkOnd pass Using Featherboards for Non Thru-SawingResawing Work SupMaking LcelSaeJArbor FenceMolding Cutting AdjustmentsMended accessories Ploughing and MoldingRip Fence Self Aligning Spring AdjustmentLock Handle Rip Fence Alignment AdjustmentAdjusting Rip Scale Indicator Slide Spring To Adjust PressureWrench To check for parallelism3t16 Locking screwsBlade Tilt, or Squareness of Blade to Table Pointer Adjusting ScrewWith Piece Screws Blade ElevationTilt and Elevation Mechanism Tilt ScrewMaintaining Your Table Saw MaintenancePivot Nut LubricationRemedy Sears Recommends the Following AccessoriesInto blade Probable CauseParts List for Craftsman 10 Inch Fable Saw Model No Repair Parts201 Parts List for Craftsman 10 Inch Table Saw Model NoDescription Parts List for Craftsman 10 Inch Table Saw Model No. t201!17 Parts list for Craftsman 10 Inch Table SawKey Pad No Description Parts List for Craftsman 10 Inch Table Saw ModelRepair Parts Model Parts List for Craftsman 10 Inch Table SawModel No Rear Guide Bar RefKey Foot Leveling Key jCo., Hoffman Estates, IL U.S.A For the repair or replacement paris you needFor in-home major brand repair service Sears, Roebuck