Craftsman 113.29921 Rip Fence Alignment Adjustment, Adjusting Rip Scale Indicator, Lock Handle

Page 38

Adjustments (continued) ..........

Adjusting the Spring 1 Loosen the screws

2.Move spring slightly toward front of fence Tighten screws

	If the fence does not slide easily along the bars, the pres-
	sure of the spring can be reduced.			Spring
	1	Loosen	the screws	Spring
	1	Loosen	the screws
	2	Move	spring slightly toward rear of fence Tighten	Screws
		screws

i

....

, i,

i,,11,,

r,_tl

,,

i,i1,1

....

Rip Fence Alignment Adjustment

WARNING: A misaligned rip fence can cause kick- backs and jams_ To avoid injury, follow these instructions until the fence is properly aligned,

The rip fence must be parallel with the sawbtade and miter gauge grooves Move fence until it is along side of groove Do not lock it. It should be parallel to groove tf it is not:

1.Loosen the hex head screws

2.Hold fence head tightly against bar Move end of fence so that it is parallel with groove

3 Alternately tighten the screws

4 Recheck alignment_

5. Repeat steps, as needed.

Adjusting Rip Scale Indicator

1 Turn elevation handwheel clockwise until blade is up as high as it wilt go

IMPORTANT: Blade must be square (90°) to table, in order to align rip fence

2oUsing a rule, position fence on right side of sawbtade 2 \ inches from the side of the teeth, tighten lock handle

3 Loosen screw holding the indicator, adjust so that it points to "2" on the rip scale, tighten screw.

NOTE: If you cannot adjust indicator so that it points to "2", loosen the screws holding the front guide bar and move the guide bar.

Slide Spring To

Adjust Pressure

Fence Head

Lock Handle

38

Image 38

Contents Sears, Roebuck and Co., Hoffman Estates, IL US,A Two Table ExtensionsRip Fence Miter Gauge Save This Manual For Future ReferenceWhen Installing Or Moving The Saw Safety Instructions For Table SawSafety Signal Words Before Using The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, ILBefore Each Use Plan Ahead To Protect Your Eyes, Hands, Face and Ears Safety Instructions For Table SawsDress for safety Whenever Sawblade Is SpinningGrain Additional Safety InstructionsWhile Thru-sawing FeatherboardMolding Glossary of Terms for WoodworkingMiter Cut Properly Prong Plug Grounded Prong Outlet Motor Specifications110-120Volt, 60 Hz. Tool Information Make sure thisExtension Wire Sizes Required Cord Length For A.W.G Motor Specifications and ElectricalWire Sizes RequirementsContents Unpacking and Checking Contents Parts ListLoose Loose PartsInstalling Handwheels and Bevel Pointer Assembling Steel LegsBench Mounting Mounting Your SawLeg Set Flat Washer Assembly Assembling Table ExtensionsInstalling Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas herCould be hit or cut Wire TieAligning Extensions ExtensionChecking Table Insert Leveling Tab EdgeInstalling Blade Guard Port AndBracket To Rip Fence On-Off SwitchGetting to Know Your Table Saw Exacti-Cut Table Insert Tilt Handwheel Elevation HandwheelLock Knob Removing and Installing Sawblade Push To TighenInspect your saw Safety Instructions for Basic Saw OperationsBefore Each Use Inspect Your BladeDont Force Tool Planyour cutAvoid Accidental Starting Push Block Work Feed DevicesPush Stick 3E-l!2rL Thick Plywood Base Auxiliary FenceMaking the handle Thick Side Plywood Finished Auxiliary FenceBasic Saw Operations Using the Miter GaugeAdditional Safety Instructions for Crosscutting CrosscuttingCrosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Ripping Using the Rip FenceAdditional Safety instructions for Rip Cuts Always Support Long Or Wide WorkpiecesPush Block Work Using Featherboards for Thru-SawingBevel Ripping Narrow Work Featherhoar FacingWork Sup Using Featherboards for Non Thru-SawingResawing Ond passFence LcelSaeJArbor MakingPloughing and Molding AdjustmentsMended accessories Molding CuttingSelf Aligning Spring Adjustment Rip FenceSlide Spring To Adjust Pressure Rip Fence Alignment AdjustmentAdjusting Rip Scale Indicator Lock HandleLocking screws To check for parallelism3t16 WrenchPointer Adjusting Screw Blade Tilt, or Squareness of Blade to TableWith Piece Tilt Screw Blade ElevationTilt and Elevation Mechanism ScrewsMaintenance Maintaining Your Table SawLubrication Pivot NutSears Recommends the Following Accessories RemedyProbable Cause Into bladeRepair Parts Parts List for Craftsman 10 Inch Fable Saw Model NoParts List for Craftsman 10 Inch Table Saw Model No 201Parts List for Craftsman 10 Inch Table Saw Model No. t DescriptionParts list for Craftsman 10 Inch Table Saw 201!17Parts List for Craftsman 10 Inch Table Saw Model Key Pad No DescriptionRepair Parts Parts List for Craftsman 10 Inch Table Saw ModelKey Model NoRear Guide Bar Ref Key j Foot LevelingSears, Roebuck For the repair or replacement paris you needFor in-home major brand repair service Co., Hoffman Estates, IL U.S.A