Craftsman 113.29921 owner manual Mounting Your Saw, Leg Set Flat Washer, Bench Mounting

Page 13

Mounting Your Saw

1 From the bag labeled "Base" remove the following hardware:

*4 Hex Head Screws, 5/16-18 x 1-I/8" Long *4 Hex Nuts, 5/16-18

*4 Lockwashers, 5/16" External Type

*8 Fiat Washers, tl/32 x 11/16 x 1/16

items marked with asterisk (*) are shown actual size

2 Place the saw upside down onto a smooth piece of cardboard or heavy paper, on the floor, so the saw is resting on the table top

WARNING: The saw is heavy. To avoid back injury, get help to lift the saw. Hold the saw close to your body. Bend your knees so you can lift with your

3.Place legs on saw so that holes in saw base and leg set line up and trim label is facing front. Legs will over- hang base in rear

4.Install screw, washers, lockwasher and nut as shown

5 Tighten all leg assembly and mounting hardware at this time

Hex

Leg Set

Flat Washer

End Stiffener

Flat Washer

Hex Head Screw

Saw Base

NOTE: For clarity, later manual illustrations may not show leg set attached

Bench Mounting

If you do net use the legset and prefer to mount the saw on a bench, make sure that there is an opening in the top of the bench the same size as the opening in the bottom of the saw so that the sawdust can drop through Recom- mended working height is 33 to 37 inches from the top of the saw table to the floor

5t16-18x 1-1/8 In	5/16-18
Hex Head Screw	Hex Nut

5/16 In External

Lockwasher11/32 LD.

Flat Washer

Cardb,

14-3/412

1/2--,--_l

Front of Saw

NOTE: All dimensions in inches

13

Image 13

Contents Rip Fence Miter Gauge Two Table ExtensionsSears, Roebuck and Co., Hoffman Estates, IL US,A Save This Manual For Future ReferenceSafety Signal Words Before Using The Saw Safety Instructions For Table SawWhen Installing Or Moving The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, ILBefore Each Use Dress for safety Safety Instructions For Table SawsPlan Ahead To Protect Your Eyes, Hands, Face and Ears Whenever Sawblade Is SpinningWhile Thru-sawing Additional Safety InstructionsGrain FeatherboardMiter Cut Glossary of Terms for WoodworkingMolding 110-120Volt, 60 Hz. Tool Information Motor SpecificationsProperly Prong Plug Grounded Prong Outlet Make sure thisWire Sizes Motor Specifications and ElectricalExtension Wire Sizes Required Cord Length For A.W.G RequirementsContents Unpacking and Checking Contents Loose ListParts Loose PartsAssembling Steel Legs Installing Handwheels and Bevel PointerLeg Set Flat Washer Mounting Your SawBench Mounting Assembling Table Extensions AssemblyInstalling Rip Fence Guide Bars and Switch Lockwas her Hex Nuts LockwashersAligning Extensions Wire TieCould be hit or cut ExtensionLeveling Tab Edge Checking Table InsertInstalling Blade Guard Port AndBracket To Getting to Know Your Table Saw On-Off SwitchRip Fence Exacti-Cut Table Insert Tilt Handwheel Elevation HandwheelLock Knob Push To Tighen Removing and Installing SawbladeBefore Each Use Safety Instructions for Basic Saw OperationsInspect your saw Inspect Your BladeAvoid Accidental Starting Planyour cutDont Force Tool Push Stick Work Feed DevicesPush Block Making the handle Auxiliary Fence3E-l!2rL Thick Plywood Base Thick Side Plywood Finished Auxiliary FenceAdditional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations CrosscuttingCrosscutting Bevel Crosscutting Miter CrosscuttingCompound Crosscutting Additional Safety instructions for Rip Cuts Using the Rip FenceRipping Always Support Long Or Wide WorkpiecesPush Block Bevel Ripping Narrow Work Using Featherboards for Thru-SawingWork Featherhoar FacingResawing Using Featherboards for Non Thru-SawingWork Sup Ond passArbor LcelSaeJFence MakingMended accessories AdjustmentsPloughing and Molding Molding CuttingRip Fence Self Aligning Spring AdjustmentAdjusting Rip Scale Indicator Rip Fence Alignment AdjustmentSlide Spring To Adjust Pressure Lock Handle3t16 To check for parallelismLocking screws WrenchBlade Tilt, or Squareness of Blade to Table Pointer Adjusting ScrewWith Piece Tilt and Elevation Mechanism Blade ElevationTilt Screw ScrewsMaintaining Your Table Saw MaintenancePivot Nut LubricationRemedy Sears Recommends the Following AccessoriesInto blade Probable CauseParts List for Craftsman 10 Inch Fable Saw Model No Repair Parts201 Parts List for Craftsman 10 Inch Table Saw Model NoDescription Parts List for Craftsman 10 Inch Table Saw Model No. t201!17 Parts list for Craftsman 10 Inch Table SawKey Pad No Description Parts List for Craftsman 10 Inch Table Saw ModelRepair Parts Model Parts List for Craftsman 10 Inch Table SawRear Guide Bar Ref Model NoKey Foot Leveling Key jFor in-home major brand repair service For the repair or replacement paris you needSears, Roebuck Co., Hoffman Estates, IL U.S.A