Graco 313289s important safety instructions Update USB Module Software, Replace USB Module

Page 33

Update USB Module Software

1.Remove shroud. See Remove Shroud.

2.Use software token 16A265. See Graco Control Architecture™ Module Programming manual for instructions.

NOTE: Upgrade all modules in the system to the software version on the token, even if you are replacing only one or two modules. Different soft- ware versions may not be compatible.

All data in the module may be reset to factory default settings. Record all settings and user prefer- ences before the upgrade, for ease of restoring them following the upgrade.

The latest software version for each system can be found at Tech Support at www.graco.com.

Repair

Replace USB Module

1.Remove shroud. See Remove Shroud.

2.Disconnect power.

3.Remove four nuts (4); leave two nuts on left side of panel tight. Open front panel of control box (11).

4.Disconnect CAN cables and USB cable from USB module (219).

5.Remove two mounting screws from USB module and remove module from base.

r_312359_313289_23a

219

6.Follow steps in reverse order to install new USB module.

7.Load software. See Update USB Module Soft-

ware.

313289S

33

Image 33

Contents XM Plural-Component Sprayers313289S Contents Related Manuals Component Manuals in U.S. EnglishManual Description Fire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Location Category Key ModelsXM a XM B XM D XM C XM E ApprovalsIsocyanate Hazard OverviewMaterial Self-Ignition Moisture Sensitivity IsocyanatesComponents a and B Changing MaterialsKeep Components a and B Separate Lift Using a Hoist Lift Using a ForkliftBefore Repair Location Proper Lifting of SprayerPressure Relief Procedure Relieve a and B Fluid PressureRelieve Pump Fluid Pressure Flush Before Using Equipment Flush Mixed Material FlushFlush Mix Manifold Use Solvent PumpFollow Pressure Relief Procedure, Empty and Flush Entire System new sprayer or end of job ProcedureGuidelines Turn on heaters until fluid lines are clear of sol- ventR3123593132896 R3123593132897 Relieve pressure. See Pressure Relief Procedure, Cleaning ProcedureShutdown Entire System Flush Entire System new sprayer or end of job onXM Setup and Troubleshooting Guide Problem Cause Solution TroubleshootingSee Appendix a in manual Tor Power Supply Control Compo View Alarms AlarmsDiagnose Alarms Clear AlarmsAlarm Code Alarm Problem When Active Cause Solution Alarm Codes and TroubleshootingSee Pump Assembly, Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Mode Control Logic Alarms Possible Alarms by ModeR2D StopAlarm Code Key LED Diagnostic InformationModule Status LED Signal Diagnosis Solution What Alert WhereReplace Air Filter Element RepairMain Air Inlet Manifold Filter Both FiltersRemove Shroud User Interface/Control BoxReplace Solenoid Module DVA DVBUpdate USB Module Software Load software. See Update USB Module Soft WareReplace USB Module Update Fluid Control Module FCM Software Load software. See Update Fluid Control Module FCM SoftwareReplace Fluid Control Module FCM Replace Alarm Upgrade SoftwareDisplay Replace Display Replace Display BatteryWall Power Supply Control Components Replace Power Supply ModuleReplace Front Panel Alternator Module Repair Alternator Power Supply Control ComponentsFCM USBReplace Alternator Regulator Air Controls Gauge 326 319 330 340 331 Fluid Control Assembly Dosing Valve AssemblyMix Manifold Assembly Temperature RTD Sensor SensorsReplace Fluid Pressure Sensor Pump Assembly Remove Pump AssemblyRemove Displacement Pump Remove Air Motor Solvent Pump Service and RepairFluid Heaters ReplaceSimplified Electrical Schematic, XM Sprayer with Alternator Electrical SchematicsElectrical Schematics 313289S Simplified Pneumatic Schematic, XM Sprayer with Alternator313289S Detailed Electrical Schematic, XM Sprayer with AlternatorBlue Green Detailed Electrical Schematic, XM Sprayer with AlternatorXM Plural Component Sprayer with Wall Power Simplified Electrical Schematic, XM Sprayer with Wall PowerSimplified Pneumatic Schematic, XM Sprayer with Wall Power Manual With Wall PowerDetailed Electrical Schematic, XM Sprayer with Wall Power Box Wiring SchematicsFluid HeatersHopper Heaters Junction Box Wiring Schematics 313289S XM Plural-Component Sprayers PartsXM1, XM2 XM3, XM4XMB and XME XM5, XM6XM7, XM8 Models 113 114 120 121 122 135 137 115 Common Parts Fluid Control Assembly PartsPart Description Qty See Air Controls Module Parts,XM1 and XM2 Models Parts Varying by ModelXM1 and XM2 Models XM Plural-Component Sprayer Models Part Description XM3 and XM4 ModelsXM3 and XM4 Models XM5 and XM6 Models Adapter XM7 and XM8 Models XM7 and XM8 Models Control Box 255771 Parts Air Power and Electric Power VersionsPart Description LabelMODULE, USB BaseAlternator Assembly Control Box Power Supply OptionsWall Power Supply Assembly Cable Connections Wall Power Supply AssemblyAdapter Air Controls Module 255761 PartsRegulator CouplingJunction Box 256540 Parts Switch 25ACircuit Breaker 25A Circuit Breaker 10ASENSOR, RTD Fluid Control Assembly PartsAir Inlet Manifold 255762 Parts SwivelCAP Plug Turbine Alternator Module 255728 PartsRepair and Spare Parts Reference Part Description Qty Part of AssemblyAccessories and Kits Desiccant Dryer Kit Electric Heated Hose Power Supply KitShutoff/Check Valve Kit Caster KitSystem Dimensions without Hoppers DimensionsSystem Dimensions with Hoppers Two 20-Gallon Hoppers Side MountedTwo 20-Gallon Hoppers Rear Mounted Two 7-Gallon Hoppers One 20-Gallon Hopper and One 7-Gallon HopperPTFE, Uhmwpe Technical DataGraco Information Graco Standard Warranty