Graco 313289s important safety instructions Optional User-Settable Spray Limits

Page 28

Alarms

Alarm
Code	Alarm Problem	When Active	Cause	Solution


		Optional User-Settable Spray Limits
T5A	Temperature exceeded alarm	Always, if enabled	Fluid temperature exceeded	If fluid temperature is too low,
T5B	limits		high or low alarm limits for more	return to circulation mode to
			than four minutes.	increase fluid temperature.
				Adjust heater set point if
				needed.See Heat Fluid section
				in manual 312359.

				If fluid temperature is too high,
				lower heater set point, and
				return circulation mode to cool.
				See Heat Fluid section in man-
				ual 312359.

				Adjust temperature target set-
				point. See Heat Fluid section in
				manual 312359.

P2A	Pressure exceeded advisory	Always, if enabled	Pressure exceeded high or low	Same as P5A or P5B.
P2B	limits		advisory limits for more than 15
			seconds.

T2A	Temperature exceeded tem-	Always, if enabled	Fluid temperature exceeded	Same as T5A or T5B.
T2B	perature limits		high or low limits for more than
			four minutes.

N4D	Pot life timer expired. Mixed	Spray	Have not sprayed enough vol-	Spray fluid, or flush. Resets
	fluid will cure in hoses, mixer,		ume to keep fresh mixed fluid in	when you leave spray mode.
	and gun.		the integration hose, mixer,	See manual 312359. See
			whip hose, and spray gun.	Flush, page 14.

28

313289S

Image 28

Contents XM Plural-Component Sprayers313289S Contents Component Manuals in U.S. English Related ManualsManual Description Fire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Models Location Category KeyApprovals XM a XM B XM D XM C XM EOverview Isocyanate HazardMaterial Self-Ignition Moisture Sensitivity IsocyanatesChanging Materials Components a and BKeep Components a and B Separate Lift Using a Forklift Lift Using a HoistBefore Repair Location Proper Lifting of SprayerRelieve a and B Fluid Pressure Pressure Relief ProcedureRelieve Pump Fluid Pressure Flush Before Using Equipment Flush Flush Mixed MaterialFlush Mix Manifold Use Solvent PumpFollow Pressure Relief Procedure, Procedure Empty and Flush Entire System new sprayer or end of jobGuidelines Turn on heaters until fluid lines are clear of sol- ventR3123593132896 R3123593132897 Cleaning Procedure Relieve pressure. See Pressure Relief Procedure,Shutdown Entire System Flush Entire System new sprayer or end of job onXM Setup and Troubleshooting Guide Troubleshooting Problem Cause SolutionSee Appendix a in manual Tor Power Supply Control Compo Alarms View AlarmsDiagnose Alarms Clear AlarmsAlarm Codes and Troubleshooting Alarm Code Alarm Problem When Active Cause SolutionSee Pump Assembly, Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Possible Alarms by Mode Mode Control Logic AlarmsR2D StopLED Diagnostic Information Alarm Code KeyModule Status LED Signal Diagnosis Solution What Alert WhereRepair Replace Air Filter ElementMain Air Inlet Manifold Filter Both FiltersUser Interface/Control Box Remove ShroudReplace Solenoid Module DVA DVBLoad software. See Update USB Module Soft Ware Update USB Module SoftwareReplace USB Module Load software. See Update Fluid Control Module FCM Software Update Fluid Control Module FCM SoftwareReplace Fluid Control Module FCM Upgrade Software Replace AlarmDisplay Replace Display Battery Replace DisplayReplace Power Supply Module Wall Power Supply Control ComponentsReplace Front Panel Alternator Power Supply Control Components Alternator Module RepairFCM USBReplace Alternator Regulator Air Controls Gauge 326 319 330 340 331 Dosing Valve Assembly Fluid Control AssemblyMix Manifold Assembly Sensors Temperature RTD SensorReplace Fluid Pressure Sensor Remove Pump Assembly Pump AssemblyRemove Displacement Pump Remove Air Motor Service and Repair Solvent PumpFluid Heaters ReplaceElectrical Schematics Simplified Electrical Schematic, XM Sprayer with AlternatorSimplified Pneumatic Schematic, XM Sprayer with Alternator Electrical Schematics 313289SDetailed Electrical Schematic, XM Sprayer with Alternator 313289SDetailed Electrical Schematic, XM Sprayer with Alternator Blue GreenSimplified Electrical Schematic, XM Sprayer with Wall Power XM Plural Component Sprayer with Wall PowerSimplified Pneumatic Schematic, XM Sprayer with Wall Power With Wall Power ManualDetailed Electrical Schematic, XM Sprayer with Wall Power Wiring Schematics BoxFluid HeatersHopper Heaters Junction Box Wiring Schematics 313289S Parts XM Plural-Component SprayersXM1, XM2 XM3, XM4XM5, XM6 XMB and XMEXM7, XM8 Models 113 114 120 121 122 135 137 115 Fluid Control Assembly Parts Common PartsPart Description Qty See Air Controls Module Parts,Parts Varying by Model XM1 and XM2 ModelsXM1 and XM2 Models XM3 and XM4 Models XM Plural-Component Sprayer Models Part DescriptionXM3 and XM4 Models XM5 and XM6 Models Adapter XM7 and XM8 Models XM7 and XM8 Models Air Power and Electric Power Versions Control Box 255771 PartsPart Description LabelBase MODULE, USBControl Box Power Supply Options Alternator AssemblyWall Power Supply Assembly Wall Power Supply Assembly Cable ConnectionsAir Controls Module 255761 Parts AdapterRegulator CouplingSwitch 25A Junction Box 256540 PartsCircuit Breaker 25A Circuit Breaker 10AFluid Control Assembly Parts SENSOR, RTDSwivel Air Inlet Manifold 255762 PartsCAP Plug Alternator Module 255728 Parts TurbinePart Description Qty Part of Assembly Repair and Spare Parts ReferenceAccessories and Kits Electric Heated Hose Power Supply Kit Desiccant Dryer KitShutoff/Check Valve Kit Caster KitDimensions System Dimensions without HoppersTwo 20-Gallon Hoppers Side Mounted System Dimensions with HoppersTwo 20-Gallon Hoppers Rear Mounted One 20-Gallon Hopper and One 7-Gallon Hopper Two 7-Gallon HoppersTechnical Data PTFE, UhmwpeGraco Standard Warranty Graco Information