Graco 313289s Sensors, Replace Fluid Pressure Sensor, Temperature RTD Sensor

Page 43

Sensors

Replace Fluid Pressure Sensor

1.Close main air shutoff valve on air supply line and on system.

2.Relieve fluid pressure. See Pressure Relief Proce- dure, page 12.

3.Open control box cover. See User Interface/Con- trol Box, page 32.

4.Disconnect pressure sensor (507) from FCM (218).

5.Disconnect fluid pressure sensor (507) from dosing valve (501).

501

506				Cord Grip	507
506				Cord Grip

r__312359_313289_30

6.Replace with new fluid pressure sensor, and recon- nect pressure sensor to FCM.

Repair

Temperature (RTD) Sensor

1.Close main air shutoff valve on air supply line and on system.

2.Relieve fluid pressure. See Pressure Relief Proce- dure, page 12.

3.Open control box cover. See User Interface/Con- trol Box, page 32.

4.Disconnect temperature sensors (506) from FCM (218).

507

506

#6 218

#5 r_xm1a00_312359_313289_15a

5.Remove RTD (506) cable from cord grip.

6.Replace with new temperature (RTD) sensor.

7.Reassemble RTD cable (506) and cord grip.

8.Connect temperature (RTD) sensor to FCM connec- tor #5. Do not use connect #6.

9.Close control box cover.

313289S

43

Image 43

Contents XM Plural-Component Sprayers313289S Contents Component Manuals in U.S. English Related ManualsManual Description Fire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Location Category Key ModelsXM a XM B XM D XM C XM E ApprovalsMoisture Sensitivity Isocyanates OverviewIsocyanate Hazard Material Self-IgnitionChanging Materials Components a and BKeep Components a and B Separate Location Proper Lifting of Sprayer Lift Using a ForkliftLift Using a Hoist Before RepairRelieve a and B Fluid Pressure Pressure Relief ProcedureRelieve Pump Fluid Pressure Flush Before Using Equipment Use Solvent Pump FlushFlush Mixed Material Flush Mix ManifoldFollow Pressure Relief Procedure, Turn on heaters until fluid lines are clear of sol- vent ProcedureEmpty and Flush Entire System new sprayer or end of job GuidelinesR3123593132896 R3123593132897 Flush Entire System new sprayer or end of job on Cleaning ProcedureRelieve pressure. See Pressure Relief Procedure, Shutdown Entire SystemXM Setup and Troubleshooting Guide Problem Cause Solution TroubleshootingSee Appendix a in manual Tor Power Supply Control Compo Clear Alarms AlarmsView Alarms Diagnose AlarmsAlarm Code Alarm Problem When Active Cause Solution Alarm Codes and TroubleshootingSee Pump Assembly, Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Stop Possible Alarms by ModeMode Control Logic Alarms R2DWhat Alert Where LED Diagnostic InformationAlarm Code Key Module Status LED Signal Diagnosis SolutionBoth Filters RepairReplace Air Filter Element Main Air Inlet Manifold FilterDVA DVB User Interface/Control BoxRemove Shroud Replace Solenoid ModuleLoad software. See Update USB Module Soft Ware Update USB Module SoftwareReplace USB Module Load software. See Update Fluid Control Module FCM Software Update Fluid Control Module FCM SoftwareReplace Fluid Control Module FCM Upgrade Software Replace AlarmDisplay Replace Display Replace Display BatteryReplace Power Supply Module Wall Power Supply Control ComponentsReplace Front Panel USB Alternator Power Supply Control ComponentsAlternator Module Repair FCMReplace Alternator Regulator Air Controls Gauge 326 319 330 340 331 Dosing Valve Assembly Fluid Control AssemblyMix Manifold Assembly Sensors Temperature RTD SensorReplace Fluid Pressure Sensor Remove Pump Assembly Pump AssemblyRemove Displacement Pump Remove Air Motor Replace Service and RepairSolvent Pump Fluid HeatersSimplified Electrical Schematic, XM Sprayer with Alternator Electrical SchematicsElectrical Schematics 313289S Simplified Pneumatic Schematic, XM Sprayer with Alternator313289S Detailed Electrical Schematic, XM Sprayer with AlternatorBlue Green Detailed Electrical Schematic, XM Sprayer with AlternatorXM Plural Component Sprayer with Wall Power Simplified Electrical Schematic, XM Sprayer with Wall PowerSimplified Pneumatic Schematic, XM Sprayer with Wall Power Manual With Wall PowerDetailed Electrical Schematic, XM Sprayer with Wall Power Heaters Wiring SchematicsBox FluidHopper Heaters Junction Box Wiring Schematics 313289S XM3, XM4 PartsXM Plural-Component Sprayers XM1, XM2XM5, XM6 XMB and XMEXM7, XM8 Models 113 114 120 121 122 135 137 115 See Air Controls Module Parts, Fluid Control Assembly PartsCommon Parts Part Description QtyXM1 and XM2 Models Parts Varying by ModelXM1 and XM2 Models XM Plural-Component Sprayer Models Part Description XM3 and XM4 ModelsXM3 and XM4 Models XM5 and XM6 Models Adapter XM7 and XM8 Models XM7 and XM8 Models Label Air Power and Electric Power VersionsControl Box 255771 Parts Part DescriptionMODULE, USB BaseAlternator Assembly Control Box Power Supply OptionsWall Power Supply Assembly Cable Connections Wall Power Supply AssemblyCoupling Air Controls Module 255761 PartsAdapter RegulatorCircuit Breaker 10A Switch 25AJunction Box 256540 Parts Circuit Breaker 25ASENSOR, RTD Fluid Control Assembly PartsSwivel Air Inlet Manifold 255762 PartsCAP Plug Turbine Alternator Module 255728 PartsRepair and Spare Parts Reference Part Description Qty Part of AssemblyAccessories and Kits Caster Kit Electric Heated Hose Power Supply KitDesiccant Dryer Kit Shutoff/Check Valve KitSystem Dimensions without Hoppers DimensionsTwo 20-Gallon Hoppers Side Mounted System Dimensions with HoppersTwo 20-Gallon Hoppers Rear Mounted Two 7-Gallon Hoppers One 20-Gallon Hopper and One 7-Gallon HopperPTFE, Uhmwpe Technical DataGraco Information Graco Standard Warranty