I.C.T.C. Holdings Corporation 300S Legend owner manual Outgo Valve, Special Notes

Page 24

OUTGO VALVE

Tools or Supplies Required

♦

Vise

♦

5/8” Open end wrench

 

 

 

 

 

 

 

 

 

♦ 11/16” Open end wrench

♦

1” Open end wrench

 

 

 

 

 

 

 

 

 

 

 

♦

Teflon Tape or pipe sealant.

 

 

 

 

 

 

 

1Open prime valve, (ref# 34) in order to release pressure from the material side of pump.

2Remove pressure control knob, (ref# 74) and pull P.C. stem, (ref# 77) out to internal stop, thereby releasing hydraulic pressure.

3Disconnect outgo tee, (ref# 33) from outgo swivel, (ref# 30) on the outgo valve.

4Remove outgo valve from machine by turning counter clockwise.

5Invert valve and secure upper part of valve, (ref# 29) in vise.

6Remove lower half of valve, (ref# 23).

7Remove crush washer, (ref# 24), seat, (ref# 26), ball, (ref# 26), cage, (ref# 27) and spring, (ref# 28). Clean and inspect all parts for wear. Replace any worn parts.

8Apply Teflon tape to threads of outgo upper body.

9Place spring, large end first, into outgo body. Spring should fit into slot machined into tunnel.

10Place cage onto spring, with open end up.

NOTE: Cage should be open so that it drags down the sides of the tunnel during installation. If closed too much it will trap the ball and cause pulsation in spray pattern.

11Place ball into cage.

12Install seat, beveled side down to ball. Seat should fit snugly into outgo body. Press on seat to ensure it will compress until it is flush with outgo body. Release slowly to ensure the parts do not dislodge themselves.

13Place crush washer on seat. Replace crush washer if badly crushed.

14Thread outgo lower onto outgo upper until finger tight. Tighten 1/2 turn with wrench. NOTE: Teflon tape or pipe sealant should be used.

15Attach repaired valve to machine, installing a new crush washer, (ref# 21) following steps 3-4 in reverse order.

SPECIAL NOTES:

♦To check the ball for wear, place against a new seat and check sealing edge against a bright light.

♦A used seat may be checked in a similar manner using a new ball. Replace used part if light pass at sealing edge.

Outgo swivel

ref# 30

29

28

27

26

25

24

23

21

H.E.R.O. INDUSTRIES

24

300S / 300SL LEGEND Owner’s Manual

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Airless Spray Equipment R.O. Warranty R.O. IndustriesTable of Contents Important Safety Precautions Always AlwaysR.O. Airless Spray Painting Operating InstructionsRead this Manual Thoroughly Setting UP to Spray Flushing the Unit AT Shutdown Or Color Change Special Storage InstructionsSpecial Notes and Instructions Airless Spray Painting Suggestions and Technique For Excellent RESULTS, Read and Practice These TechniquesPoor Good Tailing Good Pattern Fog, Over Spray Spray TIP Replacement TIP Size For ApplicationOrifice Size FAN WidthGPM Coatings Filter Orifice Viscosity Mesh SizeTroubleshooting Paint Intake Valve Assembly REF# Hydraulic Intake Valve REF# 62Hydraulic Outgo Valve REF# 73, 4-27C Paint Outgo Valve REF# 22, 4-11A Prime Valve REF# 34, 4-606 NEWPressure Test Electric Motor Wont START/RUN Electric Motor STALLS/QUITSNo PRESSURE, Blue Hydraulic Fluid in Paint Puddle of OIL Appearing Under Sprayer During Operation Sprayer does not Prime with Paint Sprayer does not Prime with Correct ThinnerSpray Material Leaks AT Prime Valve Stem Spray Material Leaks OUT Prime Valve Hose with Valve ClosedSpray Pattern is Spotty or Uneven Spray Pattern Leaves Lines or FingersReplacement of Intake Seat Tools or Supplies RequiredOutgo Valve Special NotesBleed Valve Repair Kit Installation Repair of Bleed ValveDiaphragm Replacement Hydraulic Head Insert Replacement Piston Repairs Piston Repairs Pressure Control Valve Accessories Parts List Description QTYAssy Diaphragm Assembly KITHydraulic Parts Drive Parts 300SL only Chassis Parts Parts Schematic 300S / 300SL Legend 300SLIndustries 300S / 300SLR.O. Industries 2719 Lake City WAY BURNABY, B.C Canada

300S Legend specifications

I.C.T.C. Holdings Corporation has earned a distinct reputation in the aviation industry with its flagship product, the 300S Legend. This advanced aircraft represents a significant leap forward in design and technology, combining performance, comfort, and cutting-edge features.

One of the most notable characteristics of the 300S Legend is its impressive aerodynamic efficiency. This aircraft incorporates a sleek fuselage design paired with advanced wing technologies, which contribute to enhanced stability and fuel efficiency. The wings are crafted from lightweight composite materials, enabling the 300S Legend to achieve superior lift during takeoff and landing.

The cockpit of the 300S Legend is a testament to modern aviation engineering. It is equipped with a state-of-the-art avionics suite that includes touchscreen displays, providing pilots with intuitive controls and easy access to flight data. The integration of advanced navigation systems ensures precise routing and enhanced safety, allowing pilots to operate the aircraft with confidence in various weather conditions.

In terms of performance, the 300S Legend is powered by cutting-edge engines that deliver exceptional thrust while minimizing fuel consumption. This not only extends the aircraft's range but also reduces operational costs, making it an attractive choice for commercial operators. The powerplant features advanced noise reduction technologies, ensuring compliance with stringent environmental regulations and providing a quieter cabin experience for passengers.

The interior of the 300S Legend is designed with passenger comfort in mind. The cabin boasts spacious seating arrangements, with customizable configurations to suit different missions, whether it be corporate travel or cargo transport. Large windows provide ample natural light, creating an inviting and comfortable atmosphere. The use of premium materials and finishes further enhances the overall experience, making travel not only efficient but also enjoyable.

Safety is paramount in the design of the 300S Legend, which is equipped with redundant systems and advanced safety features that meet and exceed regulatory requirements. Enhanced turbulence prediction systems and advanced autopilot functionalities contribute to a secure flying experience, ensuring that both passengers and crew are protected throughout the journey.

In conclusion, I.C.T.C. Holdings Corporation's 300S Legend combines innovative technologies with outstanding design to redefine the standards of modern aviation. Its commitment to performance, safety, and passenger comfort positions it as a leading choice for those seeking a versatile and reliable aircraft.
Top Page Image Contents