I.C.T.C. Holdings Corporation Troubleshooting Your H.E.R.O. Airless Paint Sprayer

Page 19

TROUBLESHOOTING

SITUATION

POSSIBLE CAUSE (REMEDY)

TOTAL LOSS OF PRESSURE, DIAPHRAGM HAS NO MOVEMENT OR MOVEMENT CAN BE STOPPED...CONTINUED.

2.Air lock created on hydraulic side of pump. (air entering hydraulic side due to loose hydraulic feed line fittings, (ref# 63), punctured hydraulic feed line, poor seal at hydraulic intake valve, (ref# 62), or elbow, (ref# 61). Tighten hydraulic feed line, test for leaks, or apply Teflon tape or pipe sealant on fittings. Purge air as per detailed instructions below).

3.Pressure control valve ball (ref# 87) worn out/jammed. (remove hydraulic return line, (ref# 72), from pressure control valve fitting, (ref# 81). Remove pressure control valve, (ref# 73), from elbow, (ref# 61). Disassemble pressure control valve, by removing valve seat, (ref# 86), from body, (ref# 82). Inspect for and remove foreign material. Inspect ball for wear. Install pressure control repair kit, (ref# 88), if necessary).

4.Piston rod (ref# 93) disconnected from piston (ref# 91). (reconnect piston rod following detailed instructions on page 28-29).

NO PRESSURE, BLUE HYDRAULIC FLUID IN PAINT

1.Diaphragm broken. (replace with complete diaphragm, (ref# 51). Closely follow detailed instructions on page 26. NOTE; If, and only if, paint has contaminated the hydraulic side of the pump, the entire hydraulic system must be cleaned and flushed. Make sure to remove and clean the hydraulic tank screen, (ref# 66), during this process. Refill only with genuine H.E.R.O. LVO hydraulic fluid.

NOTE; If lacquer has contaminated the hydraulic system, the piston seal, (ref# 90), must be changed in addition to flushing the system. Closely follow detailed instructions on page 28-29).

HYDRAULIC SIDE OF PUMP HAS BEEN REPAIRED AND REASSEMBLED, DIAPHRAGMNOT MOVING "PURGING"

1.Air lock created on hydraulic side of pump. (when the hydraulic side of the pump is working there is no air in it. During repairs it is possible that air has been trapped in the hydraulic system. It must be removed or the pump will not work. To purge the air from the hydraulic system; remove the pressure control knob, (ref# 74), from the valve. Gently pull the P.C. stem, (ref# 77), out. It will pull out about 1/8". Remove the vented hydraulic cap, ref# 68), from the hydraulic tank, (ref# 65), and install accessory pressure cap, item 4-45-3. With a bicycle pump, apply a few pounds of air pressure to the hydraulic tank. This will force the oil through the hydraulic system and push out any of the trapped air. Wait a few minutes. Remove pressure cap and replace with vented cap. Restart the unit and install pressure control knob.

NOTE: Unit may be running during purging procedure to speed up the procedure. If a pressure cap is unavailable, simply running the equipment for approximately 5-10 minutes with the P.C. stem pulled out, will purge the system).

Accessory

Item

4-45-3

H.E.R.O. INDUSTRIES

19

300S / 300SL LEGEND Owner’s Manual

Image 19
Contents Airless Spray Equipment R.O. Industries R.O. WarrantyTable of Contents Important Safety Precautions Always AlwaysOperating Instructions R.O. Airless Spray PaintingRead this Manual Thoroughly Setting UP to Spray Special Storage Instructions Flushing the Unit AT Shutdown Or Color ChangeSpecial Notes and Instructions For Excellent RESULTS, Read and Practice These Techniques Airless Spray Painting Suggestions and TechniquePoor Good Tailing Good Pattern Fog, Over Spray FAN Width Spray TIP ReplacementTIP Size For Application Orifice SizeCoatings Filter Orifice Viscosity Mesh Size GPMTroubleshooting Hydraulic Intake Valve REF# 62 Paint Intake Valve Assembly REF#Hydraulic Outgo Valve REF# 73, 4-27C Prime Valve REF# 34, 4-606 NEW Paint Outgo Valve REF# 22, 4-11APressure Test Electric Motor STALLS/QUITS Electric Motor Wont START/RUNNo PRESSURE, Blue Hydraulic Fluid in Paint Puddle of OIL Appearing Under Sprayer During Operation Sprayer does not Prime with Correct Thinner Sprayer does not Prime with PaintSpray Pattern Leaves Lines or Fingers Spray Material Leaks AT Prime Valve StemSpray Material Leaks OUT Prime Valve Hose with Valve Closed Spray Pattern is Spotty or UnevenTools or Supplies Required Replacement of Intake SeatSpecial Notes Outgo ValveRepair of Bleed Valve Bleed Valve Repair Kit InstallationDiaphragm Replacement Hydraulic Head Insert Replacement Piston Repairs Piston Repairs Pressure Control Valve Accessories Description QTY Parts ListAssy KIT Diaphragm AssemblyHydraulic Parts Drive Parts 300SL only Chassis Parts 300SL Parts Schematic 300S / 300SL Legend300S / 300SL IndustriesR.O. Industries 2719 Lake City WAY BURNABY, B.C Canada

300S Legend specifications

I.C.T.C. Holdings Corporation has earned a distinct reputation in the aviation industry with its flagship product, the 300S Legend. This advanced aircraft represents a significant leap forward in design and technology, combining performance, comfort, and cutting-edge features.

One of the most notable characteristics of the 300S Legend is its impressive aerodynamic efficiency. This aircraft incorporates a sleek fuselage design paired with advanced wing technologies, which contribute to enhanced stability and fuel efficiency. The wings are crafted from lightweight composite materials, enabling the 300S Legend to achieve superior lift during takeoff and landing.

The cockpit of the 300S Legend is a testament to modern aviation engineering. It is equipped with a state-of-the-art avionics suite that includes touchscreen displays, providing pilots with intuitive controls and easy access to flight data. The integration of advanced navigation systems ensures precise routing and enhanced safety, allowing pilots to operate the aircraft with confidence in various weather conditions.

In terms of performance, the 300S Legend is powered by cutting-edge engines that deliver exceptional thrust while minimizing fuel consumption. This not only extends the aircraft's range but also reduces operational costs, making it an attractive choice for commercial operators. The powerplant features advanced noise reduction technologies, ensuring compliance with stringent environmental regulations and providing a quieter cabin experience for passengers.

The interior of the 300S Legend is designed with passenger comfort in mind. The cabin boasts spacious seating arrangements, with customizable configurations to suit different missions, whether it be corporate travel or cargo transport. Large windows provide ample natural light, creating an inviting and comfortable atmosphere. The use of premium materials and finishes further enhances the overall experience, making travel not only efficient but also enjoyable.

Safety is paramount in the design of the 300S Legend, which is equipped with redundant systems and advanced safety features that meet and exceed regulatory requirements. Enhanced turbulence prediction systems and advanced autopilot functionalities contribute to a secure flying experience, ensuring that both passengers and crew are protected throughout the journey.

In conclusion, I.C.T.C. Holdings Corporation's 300S Legend combines innovative technologies with outstanding design to redefine the standards of modern aviation. Its commitment to performance, safety, and passenger comfort positions it as a leading choice for those seeking a versatile and reliable aircraft.