Carrier 50XJ064-104 specifications VOLTI00, SETPT03, NTFC00, HCVAV01

Configuration Screens (cont)

DESCRIPTION	VALUE*	UNITS	NAME
OMNIZONE::INTLK09: Condenser Pump
Discrete Output Point	PUMP		Name
Discrete Input Point 1	COOLOK		Name
Discrete Input Point 2	SENSDI00		Name
Discrete Interlock
Input 1 Comparison	On		Sns1Sta
Input 2 Comparison	Off		Sns2Sta
Off Persistence Time	30	sec	OffPrst
On Persistence Time	2	sec	OnPrst
Output Logic Type	Normal		LogType
Power on Delay	0	sec	PowerUp
OMNIZONE::INTLK10: Tower Request
Discrete Output Point	TOWER		Name
Discrete Input Point 1	COOLOK		Name
Discrete Input Point 2	SENSDI00		Name
Discrete Interlock
Input 1 Comparison	On		Sns1Sta
Input 2 Comparison	Off		Sns2Sta
Off Persistence Time	30	sec	OffPrst
On Persistence Time	2	sec	OnPrst
Output Logic Type	Normal		LogType
Power on Delay	0	sec	PowerUp
OMNIZONE::INTLK11: Compressor Cooling
Discrete Output Point	COMPRES		Name
Discrete Input Point 1	COOLOK		Name
Discrete Input Point 2	FAN_CDWF		Name
Discrete Interlock
Input 1 Comparison	On		Sns1Sta
Input 2 Comparison	On		Sns2Sta
Off Persistence Time	2	sec	OffPrst
On Persistence Time	30	sec	OnPrst
Output Logic Type	Normal		LogType
Power on Delay	0	sec	PowerUp
OMNIZONE::LINK_01: Linkage/AOSS Schedule 01
Setpoint Bias	VOLT_I00		Name
Setpoint Schedule	SETPT03		Name
Adaptive Optimal Start
AO Start Enable	Disable		Enable
Building Insulation	30		BldInsul
Unoccupied 24hr Factor	15		UnOccFct
Offset Low Value	0	^F	Value
Offset High Value	0	^F	Value
Sensor Group/SPT Sensor	CTRLPT		Name
Time Schedule	OCCPC01		Name
Outside Air Temp	OAT		Name
NTFC Algorithm	NTFC_00		Name
Heating Algorithm	HCVAV01		Name
Supply Air Temp	SAT		Name
Fan Status	SF_SFS		Name
Adaptive Optimal Stop
AO Stop Enable	Disable		Enable
Maximum Stop Time	60	min	MaxStop
Setpoint Bias	2	^F	SPBias
Power on Delay	0	sec	PowerUp
Evacuation	EVAC		Evacuate
Pressurization	TRMOP		Pressure
OMNIZONE::LMALM01: Supply air Sensor
Monitored Input Point	SAT		Name
Alarm Inhibit Point	SENSDI00		Name
Limit Check
Low Limit	25	dF	LowLim
High Limit	150	dF	HighLim
Enable Delay Time	15	sec	DlyTim
Persistence Time	10	sec	Persist
Hysteresis	5	^F	Hyst
Alarm Processor
Alarm Processing	Enable		AlmProc
Re-Alarm Interval	0	min	ReAlmTim
Alarm=1 or Alert=0	1		Type
Alarm Level	1		AlmLevel
Alarm Source	5		AlmSrc
Alarm Routing	11010000		AlmRtg
Alarm Description Index	7		AlmDesc
Alarm Message - Part 1			Message
Alarm Message - Part 2			Message
Alarm Message - Part 3			Message
Alarm Message - Part 4			Message
Power on Delay	0	sec	PowerUp

*Default values from factory.

NOTE: See CC6400 Comfort Controller Overview and Configuration Manual for configuration information.

55