Grizzly G0704 owner manual Unattended OPERATION. Never­ leave­

Page 11

­

DISCONNECTING POWER SUPPLY.­Always­dis- connect­ machine­ from­ power­ supply­ before­ ser- vicing,­ adjusting,­ or­ changing­ cutting­ tools­ (bits,­ blades,­ cutters,­ etc.).­ Make­ sure­ switch­ is­ in­ OFF­ position­before­reconnecting­to­avoid­an­unexpect- ed­or­unintentional­start.

APPROVED OPERATION.­ Untrained­ operators­ can­ be­ seriously­ hurt­ by­ machinery.­ Only­ allow­ trained­ or­ properly­ supervised­ people­ to­ use­ machine.­ When­ machine­ is­ not­ being­ used,­ dis- connect­ power,­ remove­ switch­ keys,­ or­ lock-out­ machine­to­prevent­unauthorized­use—especially­ around­children.­Make­workshop­kid­proof!

DANGEROUS ENVIRONMENTS. Do­ not­ use­ machinery­ in­ wet­ or­ rainy­ locations,­ cluttered­ areas,­ around­ flammables,­ or­ in­ poorly-lit­ areas.­ Keep­ work­ area­ clean,­ dry,­ and­ well-lighted­ to­ minimize­risk­of­injury.

ONLY USE AS INTENDED.­ Only­ use­ machine­ for­ its­ intended­ purpose.­ Never­ modify­ or­ alter­ machine­for­a­purpose­not­intended­by­the­manu- facturer­or­serious­injury­may­result!

USE RECOMMENDED ACCESSORIES.­Consult­ this­owner’s­manual­or­the­manufacturer­for­rec- ommended­ accessories.­ Using­ improper­ acces- sories­will­increase­the­risk­of­serious­injury.

CHILDREN & BYSTANDERS. Keep­ children­ and­bystanders­a­safe­distance­away­from­work­ area.­Stop­using­machine­if­children­or­bystand- ers­become­a­distraction.

REMOVE ADJUSTING TOOLS.­ Never­ leave­ adjustment­tools,­chuck­keys,­wrenches,­etc.­in­or­ on­machine—especially­near­moving­parts.­Verify­ removal­before­starting!

SECURING WORKPIECE.­ When­ required,­ use­ clamps­ or­ vises­ to­ secure­ workpiece.­ A­ secured­ workpiece­protects­hands­and­frees­both­of­them­ to­operate­the­machine.

FEED DIRECTION.­Unless­otherwise­noted,­feed­ work­ against­ the­ rotation­ of­ blades­ or­ cutters.­ Feeding­in­the­same­direction­of­rotation­may­pull­ your­hand­into­the­cut.

FORCING MACHINERY.­Do­not­force­machine.­ It­ will­ do­ the­ job­ safer­ and­ better­ at­ the­ rate­ for­ which­it­was­designed.

GUARDS & COVERS.­ Guards­ and­ covers­ can­ protect­ you­ from­ accidental­ contact­ with­ moving­ parts­ or­ flying­ debris.­ Make­ sure­ they­ are­ prop- erly­installed,­undamaged,­and­working­correctly­ before­using­machine.

NEVER STAND ON MACHINE.­Serious­injury­or­ accidental­ contact­ with­ cutting­ tool­ may­ occur­ if­ machine­is­tipped.­Machine­may­be­damaged.

STABLE MACHINE. Unexpected­movement­dur- ing­operations­greatly­increases­the­risk­of­injury­ and­ loss­ of­ control.­ Verify­ machines­ are­ stable/ secure­ and­ mobile­ bases­ (if­ used)­ are­ locked­ before­starting.

AWKWARD POSITIONS.­ Keep­ proper­ footing­ and­balance­at­all­times­when­operating­machine.­ Do­not­overreach!­Avoid­awkward­hand­positions­ that­ make­ workpiece­ control­ difficult­ or­ increase­ the­risk­of­accidental­injury.

UNATTENDED OPERATION. Never­ leave­

machine­running­while­unattended.­Turn­machine­ off­and­ensure­all­moving­parts­completely­stop­ before­walking­away.

MAINTAIN WITH CARE.­Follow­all­maintenance­ instructions­ and­ lubrication­ schedules­ to­ keep­ machine­in­good­working­condition.­An­improperly­ maintained­machine­may­increase­the­risk­of­seri- ous­injury.­

CHECK DAMAGED PARTS.­ Regularly­ inspect­ machine­ for­ damaged­ parts,­ loose­ bolts,­ mis- adjusted­ or­ mis-aligned­ parts,­ binding,­ or­ any­ other­ conditions­ that­ may­ affect­ safe­ operation.­ Always­repair­or­replace­damaged­or­mis-adjust- ed­parts­before­operating­machine.

EXPERIENCING DIFFICULTIES. If­ at­ any­ time­ you­ are­ experiencing­ difficulties­ performing­ the­ intended­ operation,­ stop­ using­ the­ machine!­ Contact­ our­ Technical­ Support­ Department­ at­ (570)­546-9663.

Model G0704 (Mfg. since 09/09)

-9-

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model G0704 MILL/DRILL with Stand Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification G0704 electronic controls identification Electronic Controls IdentificationMachine Data Sheet Other Features Safety Instructions for Machinery SafetyUnattended OPERATION. Never­ leave­ Additional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWGDescription Qty SetupNeeded for Setup UnpackingNot Shown Contents QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Weight LoadMoving & Placing Machine Example of a direct mount setupBolting to Concrete Floors Mounting to Shop FloorTo assemble your machine AssemblyTo install the drill chuck onto the arbor Drill Chuck ArborConnecting Power Power ConnectionTo test run and break-in the spindle bearings Test Run & Spindle Break-inSpeed Range Selector Knob Selects low range OperationsBasic Controls Digital readout unit controls Operation Overview To use the digital readout Digital Readout UnitTo determine the needed spindle speed Calculating Spindle SpeedTo set the spindle speed Spindle Speed DirectionSpindle Height Controls Changing Spindle Position Using Quill Feed LeversDrill Chuck To install the drill chuck and arborTo remove the collet To install the toolingLoading Tooling To tilt the headstock to the left or right Headstock Travel Axis and RotationTo raise or lower the headstock Cross Feed Table TravelLongitudinal Feed H8177-Worktable with Angle AccessoriesH8179 H5685-4Rotary Table G9322-Boring Head Combo SetG8683Z-Mini Shop Fox Mobile Base G5684-R-8 Vertical Collet Rack G5758-Tilt xLubrication MaintenanceSchedule To lubricate the leadscrews Tools Needed QtyHandwheel gears Troubleshooting ServiceFor proper use and safety Gibs To adjust the table gibsTo adjust the headstock gibs To replace the digital readout unit battery Battery ReplacementTo adjust the Y-axis leadscrew nut To adjust the X-axis leadscrewTo inspect and replace the motor brushes Motor ServiceWiring Safety Instructions Wiring110 VAC Wiring DiagramSide panel Rear panelColumn Breakdown PartsDescription Column Parts ListElectrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. since 09/09 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY
Top Page Image Contents